What does the reductent diagram look like?

Q: 300 mm 30° 300 mm 300 mm Can some one please label the projection of F and the rest of the…

A: Solution: The force vector F and uOA:

Q: A car is traveling at speed v when the brakes are suddenly applied, causing a constant deceleration…

A: Hello dear this is the solution of your problem The answer is found to be Distance travelled by car…

Q: Can you add the datum line in the illustration and make a bettter illustration based on solution

A: Given, Angle made by nozzle = 45o Horizontal distance = 15 to 20 m

Q: Given the calculated volume of concrete for Suspended Concrete Slab of 4,788.47 cu.m. on an…

A: Given Data:The total volume of concrete is 4788.47 cu.mThe proportion for Class AA mixture of…

Q: Problem 6: A rigid bar, hinged at one end, is supported by two identical springs as shown. Each…

A: Solution:

Q: Find the centroid of the following cross-sections and planes.

A: Centrodal distanceX = 5.333 inY = 5.667 inExplanation:Step 1:Step 2:

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: The ends of the triangular plate are subjected to three couples. Determine the magnitude of the…

A: Given:-  The ends of the triangular plate are subjected to three couples. Determine the magnitude of…

Q: For the body below, determine the centroid under the reference frame shown. Y 2

A:

Q: 5. A child in a school crossing ran into the street and was struck by a car, despite the driver…

A: Skidding occurs when a vehicle's tires lose traction on the road. When your tires lose grip, you…

Q: QUESTION Compute the reactions at support for an overhanging beam as shown in the figure. Then, draw…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: Q.12.19 A field pumping test was conducted from an aquifer of sandy soil of 4 m thickness confined…

A:

Q: QUESTION 1 Air at 80 °C flows slowly through a 500 mm circular galvanized steel duct. Determine the…

A:

Q: Replace the loading acting on the beam by a single resultant force. Specify where the force acts,…

A: To find Single resultant force, Fr and the location where it is acting, d

Q: Six steel cables are supporting a circular heavy moulding of diameter 2 m from an overhead point as…

A:

Q: 5. An elastomeric bearing pad consisting of two steel plates bonded to a chloroprene elastomer (an…

A: Given  Dimensions a= 125 mm  b= 240 mm  t= 50 mm  Shear force, V= 12 KN

Q: d the x bar location of the centroid along x axis and y bar location of the centroid along y a

A:

Q: A horizontal bar of negligible mass is hinged at A and assumed to be rigid. It is supported by an…

A:

Q: Question 1) Determine the x and z components of reaction at the journal bearing A and the tension in…

A: F1 = -800 k F2 = 350 j

Q: Resolve force F1 = 250 kN into components along the u and v axes and determine the magnitude of…

A:

Q: Problem 1: A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow…

A:

Q: Kindly include the free-body diagram too.

A: Solution: Given: Initial velocity u = 96 k,/hr u = 96×100060×60=36.67 m/s Final velocity: V = 0…

Q: Find the centroid of the following cross-sections and planes.

A: Centroid is = (0, 9.427 in)Explanation:Step 1: Calculation for centroid of given section.Thanks.

Q: 1. Determine the normal force, shear force, and moment at point C where A is pin support and B is…

A:

Q: Find the centroid of X and Y in tabular form.

A: A centroid is a point on the body on which the mass of a body is uniformly distributed. If the body…

Q: 3.24 A 30-m tape has a mass of 544 g and is sup- ported only at the ends with a force of 80 N. What…

A: Given data : Mass of tape between two support (m)=544 g Length of tape (L)=30 m Force (P)=80 N

Q: 1. Figure 1 below shows a simple beam with two concentrated loads (X and Y). a. Write the shear and…

A:

Q: An image of a hilltop is 87.5 mm from the centre of a photograph. The elevation of the hill is 665 m…

A: Given -  Height of image, r = 87.5 mm Elevation of the hill, h = 665 mm Flight altitude, H = 4660 mm…

Q: Y 1.3 in. 1.0 in. 0.5 in. 3.8 in. |0.5 in. A 3.6 in.-

A:

Q: Determine the centroid x and y

A:

Q: The centroid of the rectangle about x and y-axis is: 6m 4m 3m

A:

Q: can you please show the integration in the position? And can you please make it look like this?…

A:

Q: (3) The 32-mm-diameter shaft is used to transmit torques applied to the gears. Determine the…

A: ASKED: To compute the absolute maximum shear stress in the shaft.   Given, Diameter of the shaft (d)…