(a) Explanation Given information: The elastic modulus ( E ) is 200 GPa . The section of the beam is W 250 × 28.4 . Calculation: Refer Table, “W shape properties”, the moment of inertia ( I ) for the given section is 40.1 × 10 6 mm 4 or 40.1 × 10 − 6 m 4 . Use moment area method: Show the free body diagram of beam by considering the point load as in Figure 1. Draw the moment diagram of the above beam as in Figure 2. Calculate the moment ( M 1 ) by taking moment about point C : M 1 = 18 × 2.2 = 39.6 kN ⋅ m Calculate the ratio of M 1 E I using the relation: Ratio = M 1 E I Substitute 39.6 kN ⋅ m for M 1 , 200 GPa for E , and 40.1 × 10 6 mm 4 for I . M 1 E I = 39.6 kN ⋅ m 200 × 10 6 × 40.1 × 10 − 6 m 4 = 4.9377 × 10 − 3 m − 1 Calculate the area ( A 1 ) due to the moment ( M 1 ) using the formula: A 1 = 1 2 b 1 h 1 Here, b 1 is the width of the triangle and h 1 is the height of the triangle. Substitute 2.2 m for b 1 and 4.9377 × 10 − 3 m -1 for h 1 . A 1 = 1 2 × 2.2 × ( 4.9377 × 10 − 3 ) = 5.4315 × 10 − 3 Show the free body diagram of beam by considering the uniformly distributed load as in Figure 3. Draw the moment diagram of the above beam as in Figure 4. Calculate the moment ( M 2 ) by taking moment about point C : M 2 = − 26 × 2.7 × 2.7 2 = 94.77 kN ⋅ m Calculate the ratio of M 2 E I using the relation: Ratio = M 2 E I Substitute 94 (b) To determine Find the deflection ( y A ) at point A .

7th Edition

ISBN: 9780100257061

Author: BEER

Publisher: YUZU

See similar textbooks

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and af…

Videos

Question

Chapter 9.5, Problem 102P

(a)

To determine

Find the slope (θA) at point A.

(b)

To determine

Find the deflection (yA) at point A.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.5, Problem 101P

Chapter 9.5, Problem 103P

Students have asked these similar questions

CORRECT AND DETAILED HANDWRITTEN SOLUTION WITH FBD ONLY. I WILL UPVOTE THANK YOU. CORRECT ANSWER IS ALREADY PROVIDED. The cantilevered spandrel beam shown whose depth tapers from d1 to d2, has a constant width of 120mm. It carries a triangularly distributed end reaction.Given: d1 = 600 mm, d2 = 120 mm, L = 1 m, w = 100 kN/m1. Calculate the maximum flexural stress at the support, in kN-m.2. Determine the distance (m), from the free end, of the section with maximum flexural stress.3. Determine the maximum flexural stress in the beam, in MPa.ANSWERS: (1) 4.630 MPa; (2) 905.8688 m; (3) 4.65 MPa

CORRECT AND DETAILED HANDWRITTEN SOLUTION WITH FBD ONLY. I WILL UPVOTE THANK YOU. CORRECT ANSWER IS ALREADY PROVIDED. A concrete wall retains water as shown. Assume that the wall is fixed at the base. Given: H = 3 m, t = 0.5m, Concrete unit weight = 23 kN/m3Unit weight of water = 9.81 kN/m3(Hint: The pressure of water is linearly increasing from the surface to the bottom with intensity 9.81d.)1. Find the maximum compressive stress (MPa) at the base of the wall if the water reaches the top.2. If the maximum compressive stress at the base of the wall is not to exceed 0.40 MPa, what is the maximum allowable depth(m) of the water?3. If the tensile stress at the base is zero, what is the maximum allowable depth (m) of the water?ANSWERS: (1) 1.13 MPa, (2) 2.0 m, (3) 1.20 m

CORRECT AND DETAILED HANDWRITTEN SOLUTION WITH FBD ONLY. I WILL UPVOTE THANK YOU. CORRECT ANSWER IS ALREADY PROVIDED. A short plate is attached to the center of the shaft as shown. The bottom of the shaft is fixed to the ground.Given: a = 75 mm, h = 125 mm, D = 38 mmP1 = 24 kN, P2 = 28 kN1. Calculate the maximum torsional stress in the shaft, in MPa.2. Calculate the maximum flexural stress in the shaft, in MPa.3. Calculate the maximum horizontal shear stress in the shaft, in MPa.ANSWERS: (1) 167.07 MPa; (2) 679.77 MPa; (3) 28.22 MPa

Chapter 9 Solutions

EBK MECHANICS OF MATERIALS

Ch. 9.2 - In the following problems assume that the flexural...Ch. 9.2 - In the following problems assume that the flexural...Ch. 9.2 - In the following problems assume that the flexural...Ch. 9.2 - 9.1 through 9.4 For the loading shown, determine...Ch. 9.2 - 9.5 and 9.6 For the cantilever beam and loading...Ch. 9.2 - 9.5 and 9.6 For the cantilever beam and loading...Ch. 9.2 - For the beam and loading shown, determine (a) the...Ch. 9.2 - For the beam and loading shown, determine (a) the...Ch. 9.2 - Knowing that beam .AB is a W10 33 rolled shape...Ch. 9.2 - Knowing that beam AB is an S200 34 roiled shape...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Find the slope ( θ A ) at point A .

Solution Summary: The author shows the free body diagram of beam by considering the point load as in Figure 1.