Explanation Draw the T − s diagram for ideal Stirling engine cycle as shown in Figure (1). Write the expression to calculate the mass of the air ( m ) at state 1. m = P 1 ν 1 R T 1 (I) Here, the pressure at state 1 is P 1 , mass of air is m , the gas constant is R , the temperature at state 1 is T 1 , volume at state 1 is ν 1 . Write the expression to calculate the pressure at state 2 ( P 2 ) at the end of the compression. P 2 = P 1 ( ν 1 ν 2 ) (II) Here, volume at state 2 is ν 2 and pressure at state 2 is P 2 . Write the expression for the change in entropy for the process 1-2. ( s 2 − s 1 ) = ( s 3 − s 4 ) = c p ln T 2 T 1 − R ln P 2 P 1 For process 1-2, T 1 and T 2 are equal. ( s 2 − s 1 ) = ( s 3 − s 4 ) = c p ln T 2 T 2 − R ln P 2 P 1 ( s 2 − s 1 ) = ( s 3 − s 4 ) = 0 − R ln P 2 P 1 ( s 2 − s 1 ) = ( s 3 − s 4 ) = − R ln P 2 P 1 (III) Here, entropy at state 1 is s 1 , entropy at state 2 is s 2 , entropy at state 3 is s 3 and entropy at state 4 is s 4 . The processes are reversible. Write the expression to calculate the external heat input to the cycle ( Q in ) . Q in = m T 1 ( s 2 − s 1 ) (IV) Write the expression to calculate the external heat rejection ( Q out ) . Q out = m T 3 ( s 3 − s 4 ) (V) Write the expression to calculate heat transfer between the working fluid and regenerator for each complete cycle ( Q regenerator ) . Q regenerator = m c v ( T 1 − T 4 ) (VI) Here, specific heat of air at constant volume is c v and temperature at state 4 is T 4 . Conclusion: From Table A-1E, “Molar mass, gas constant, and critical-point properties”, obtain the value of gas constant ( R ) for hydrogen as 5.3224 psia ⋅ ft 3 / lbm ⋅ R . From Table A-2Ea, “Ideal-gas specific heats of various common gases”, obtain the Following properties for hydrogen. k = 1.404 c v = 2.44 Btu / lbm ⋅ R c p = 3.43 Btu / lbm ⋅ R Substitute 400 psia for P 1 , 0.1 ft 3 for ν 1 , 5.3224 psia ⋅ ft 3 / lbm ⋅ R for R , and 640 ° F for T 3 in Equation (I). m = ( 400 psia ) ( 0.1 ft 3 ) ( 5.3224 psia ⋅ ft 3 / lbm ⋅ R ) ( 640 ° F ) = ( 400 psia ) ( 0.1 ft 3 ) ( 5

9th Edition

ISBN: 9781266657610

Author: CENGEL

Publisher: MCG CUSTOM

See similar textbooks

Videos

Question

Chapter 9.12, Problem 78P

To determine

The amount of external heat addition, external heat rejection, and heat transfer between the working fluid and regenerator for each complete cycle.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.12, Problem 77P

Chapter 9.12, Problem 79P

Students have asked these similar questions

The network output and the thermal efficiency for the Carnot and the simple ideal Rankine cycles with steam as the working fluid are to be calculated and evaluated. Steam enters the turbine in both cases at 5 MPa as a saturated vapor, and the condenser pressure is 50 kPa. In the Rankine cycle, the condenser exit state is saturated liquid and in the Carnot cycle, the boiler inlet state is saturated liquid. Construct the T-s diagrams for both cycles.

At a given compression ratio, which cycle has a higher thermal efficiency?

The pressure ratio of a gas-turbine power plant operating on an ideal Brayton cycle is 8. The gas temperature is 300 degrees Fahrenheit at the compressor inlet and 1300 degrees Fahrenheit at the turbine inlet. Assuming an 80 percent compressor efficiency and an 80 percent turbine efficiency. A regenerator with an 80 percent efficiency is installed at the power plant. Determine the variation of particular heats with temperature using specific heats. a. The back work ratio b.The thermal efficiency

Chapter 9 Solutions

THERMODYNAMICS (LL)-W/ACCESS >CUSTOM<

Ch. 9.12 - What are the air-standard assumptions?Ch. 9.12 - What is the difference between air-standard...Ch. 9.12 - Prob. 3P Ch. 9.12 - How does the thermal efficiency of an ideal cycle,...Ch. 9.12 - How are the combustion and exhaust processes...Ch. 9.12 - What does the area enclosed by the cycle represent...Ch. 9.12 - Prob. 7P Ch. 9.12 - Can the mean effective pressure of an automobile...Ch. 9.12 - What is the difference between spark-ignition and...Ch. 9.12 - Prob. 10P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The amount of external heat addition, external heat rejection, and heat transfer between the working fluid and regenerator for each complete cycle.

Solution Summary: The author explains the amount of external heat addition, rejection, and heat transfer between the working fluid and regenerator for each complete cycle.

Videos

The amount of external heat addition, external heat rejection, and heat transfer between the working fluid and regenerator for each complete cycle.

Want to see the full answer?

Chapter 9 Solutions