a) Explanation Draw the given diesel cycle on P − v diagram as in Figure (1). Write the relationship between temperature and specific volume for the isentropic compression process 1-2from Figure (1). T 2 = T 1 ( v 1 v 2 ) k − 1 (I) Here, the temperature at state 1 is T 1 , the temperature at state 2 is T 2 , specific volume at state 1 is v 1 , specific volume at state 2 is v 2 , and the specific heat ratio is k . Write the relationship between the temperature, pressure, and specific volume for the constant pressure heat addition process 2-3. P 3 v 3 T 3 = P 2 v 2 T 2 For process 2-3, P 2 and P 3 are equal. T 3 = v 3 v 2 T 2 (II) Here, the temperature at state 3 is T 3 , specific volume at state 2 is v 2 , specific volume at state 3 is v 3 , pressure at state 3 is P 3 , pressure at state 2 is P 2 , and specific volume at state 3 is v 3 . From the Table A-2 “Ideal2gas specific heats of various common gases” obtain the below properties for air b) To determine The thermal efficiency of the given diesel cycle c) To determine The mean effective pressure for the given diesel cycle

9th Edition

ISBN: 9781266657610

Author: CENGEL

Publisher: MCG CUSTOM

See similar textbooks

Concept explainers

IC engines

The term "engine" indicates a mechanical device/machine used to convert input energy to a specific mechanical output. The input energy may be in the form of chemical energy, thermal energy, or so on and mechanical output is in the form of mechanical ener…

Question

Chapter 9.12, Problem 53P

To determine

The temperature and pressure at the end of the heat addition process

To determine

The thermal efficiency of the given diesel cycle

To determine

The mean effective pressure for the given diesel cycle

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.12, Problem 52P

Chapter 9.12, Problem 54P

Students have asked these similar questions

answer this as soon as possible, please.

A piston–cylinder device contains 50 kg of water at 250 kPa and 25°C. The cross-sectional area of the piston is 0.1 m2. Heat is now transferred to the water, causing part of it to evaporate and expand. When the volume reaches 0.26 m3, the piston reaches a linear spring whose spring constant is 100 kN/m. More heat is transferred to the water until the piston rises 20 cm more. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the work done during this process. The work done during this process is kJ.

A 4-m × 5-m × 7-m room is heated by the radiator of a steam-heating system. The steam radiator transfers heat at a rate of 10,000 kJ/h, and a 100-W fan is used to distribute the warm air in the room. The rate of heat loss from the room is estimated to be about 5000 kJ/h. If the initial temperature of the room air is 10°C, determine how long it will take for the air temperature to rise to 25°C. Assume constant specific heats at room temperature. The gas constant of air is R = 0.287 kPa·m3/kg·K (Table A-1). Also, cv = 0.718 kJ/kg·K for air at room temperature (Table A-2). Steam enters the radiator system through an inlet outside the room and leaves the system through an outlet on the same side of the room. The fan is labeled as W sub p w. The heat is given off by the whole system consisting of room, radiator and fan at the rate of 5000 kilojoules per hour. It will take 831 Numeric ResponseEdit Unavailable. 831 incorrect.s for the air temperature to rise to 25°C.

Chapter 9 Solutions

THERMODYNAMICS (LL)-W/ACCESS >CUSTOM<

Ch. 9.12 - What are the air-standard assumptions?Ch. 9.12 - What is the difference between air-standard...Ch. 9.12 - Prob. 3P Ch. 9.12 - How does the thermal efficiency of an ideal cycle,...Ch. 9.12 - How are the combustion and exhaust processes...Ch. 9.12 - What does the area enclosed by the cycle represent...Ch. 9.12 - Prob. 7P Ch. 9.12 - Can the mean effective pressure of an automobile...Ch. 9.12 - What is the difference between spark-ignition and...Ch. 9.12 - Prob. 10P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The temperature and pressure at the end of the heat addition process

Solution Summary: The author illustrates the relationship between temperature and specific volume for the isentropic compression process 1-2.

Concept explainers

The temperature and pressure at the end of the heat addition process

The thermal efficiency of the given diesel cycle

The mean effective pressure for the given diesel cycle

Want to see the full answer?

Chapter 9 Solutions