a) Explanation Write the expression for the quasi equilibrium boundary work. W b = ∫ 1 2 P d V W b = P 1 V 1 ln V 2 V 1 (I) Here, pressure at state 1 is P 1 , initial volume is V 1 , and final volume is V 2 . Write the expression for the workdone against the atmospheric pressure. W s u r r = P 0 ( V 2 − V 1 ) (II) Here, atmospheric pressure is P 0 . Write the expression for the use full work. W u = W b − W s u r r (III) Write the expression for the energy balance of the system Q i n − Q b , o u t = Δ U Q i n = Q b , o u t Here, heat transfer to the system is Q i n , heat transfer from the system to surrounding is Q b , o u t , and change in internal energy is Δ U . Conclusion: Substitute 350 kPa for P 1 , 0 .01 m 3 for V 1 , 0.02 m 3 for V 2 , and 0.01 m 3 for V 1 in equation (I) b) To determine The exergy destruction during the process c) To determine The exergy destruction during the process.

8th Edition

ISBN: 8220102809444

Author: CENGEL

Publisher: YUZU

See similar textbooks

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. T…

Videos

Question

Chapter 8.8, Problem 115RP

To determine

The use full work output during the process

To determine

The exergy destruction during the process

To determine

The exergy destruction during the process.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 8.8, Problem 114RP

Chapter 8.8, Problem 116RP

Students have asked these similar questions

motor supplies 200 kW at 6 Hz to flange A of the shaft shown in Figure. Gear B transfers 125 W of power to operating machinery in the factory, and the remaining power in the shaft is mansferred by gear D. Shafts (1) and (2) are solid aluminum (G = 28 GPa) shafts that have the same diameter and an allowable shear stress of t= 40 MPa. Shaft (3) is a solid steel (G = 80 GPa) shaft with an allowable shear stress of t = 55 MPa. Determine: a) the minimum permissible diameter for aluminum shafts (1) and (2) b) the minimum permissible diameter for steel shaft (3). c) the rotation angle of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b).

First monthly exam Gas dynamics Third stage Q1/Water at 15° C flow through a 300 mm diameter riveted steel pipe, E-3 mm with a head loss of 6 m in 300 m length. Determine the flow rate in pipe. Use moody chart. Q2/ Assume a car's exhaust system can be approximated as 14 ft long and 0.125 ft-diameter cast-iron pipe ( = 0.00085 ft) with the equivalent of (6) regular 90° flanged elbows (KL = 0.3) and a muffler. The muffler acts as a resistor with a loss coefficient of KL= 8.5. Determine the pressure at the beginning of the exhaust system (pl) if the flowrate is 0.10 cfs, and the exhaust has the same properties as air.(p = 1.74 × 10-3 slug/ft³, u= 4.7 x 10-7 lb.s/ft²) Use moody chart (1) MIDAS Kel=0.3 Q3/Liquid ammonia at -20°C is flowing through a 30 m long section of a 5 mm diameter copper tube(e = 1.5 × 10-6 m) at a rate of 0.15 kg/s. Determine the pressure drop and the head losses. .μ= 2.36 × 10-4 kg/m.s)p = 665.1 kg/m³

2/Y Y+1 2Cp Q1/ Show that Cda Az x P1 mactual Cdf Af R/T₁ 2pf(P1-P2-zxgxpf) Q2/ A simple jet carburetor has to supply 5 Kg of air per minute. The air is at a pressure of 1.013 bar and a temperature of 27 °C. Calculate the throat diameter of the choke for air flow velocity of 90 m/sec. Take velocity coefficient to be 0.8. Assume isentropic flow and the flow to be compressible. Quiz/ Determine the air-fuel ratio supplied at 5000 m altitude by a carburetor which is adjusted to give an air-fuel ratio of 14:1 at sea level where air temperature is 27 °C and pressure is 1.013 bar. The temperature of air decreases with altitude as given by the expression The air pressure decreases with altitude as per relation h = 19200 log10 (1.013), where P is in bar. State any assumptions made. t = ts P 0.0065h

Chapter 8 Solutions

EBK THERMODYNAMICS: AN ENGINEERING APPR

Ch. 8.8 - What final state will maximize the work output of...Ch. 8.8 - Is the exergy of a system different in different...Ch. 8.8 - How does useful work differ from actual work? For...Ch. 8.8 - Prob. 4P Ch. 8.8 - Consider two geothermal wells whose energy...Ch. 8.8 - Consider two systems that are at the same pressure...Ch. 8.8 - Prob. 7P Ch. 8.8 - Does a power plant that has a higher thermal...Ch. 8.8 - Prob. 9P Ch. 8.8 - 8–10C Can a process for which the reversible work...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The use full work output during the process

Solution Summary: The author explains the use of full work output during the process. Write the expression for the quasi equilibrium boundary work.

Concept explainers

Videos

The use full work output during the process

The exergy destruction during the process

The exergy destruction during the process.

Want to see the full answer?

Chapter 8 Solutions