(a)
Interpretation:
The solubility of given substance in water and benzene is to be predicted.
Concept introduction:
The term soluble is used for a pair of substances that forms a homogenous mixture. The term insoluble is used for a pair that does not mix with each other. The solubility of a substance in a solvent depends on the “like dissolve like” principle. The polar-polar substance will mix in each other and non-polar and non-polar substance will mix each other.
(b)
Interpretation:
The solubility of given substance in water and benzene is to be predicted.
Concept introduction:
The term soluble is used for a pair of substances that forms a homogenous mixture. The term insoluble is used for a pair that does not mix with each other. The solubility of a substance in a solvent depends on the “like dissolve like” principle. The polar-polar substance will mix in each other and non-polar and non-polar substance will mix each other.
(c)
Interpretation:
The solubility of given substance in water and benzene is to be predicted.
Concept introduction:
The term soluble is used for a pair of substances that forms a homogenous mixture. The term insoluble is used for a pair that does not mix with each other. The solubility of a substance in a solvent depends on the “like dissolve like” principle. The polar-polar substance will mix in each other and non-polar and non-polar substance will mix each other.
(d)
Interpretation:
The solubility of given substance in water and benzene is to be predicted.
Concept introduction:
The term soluble is used for a pair of substances that forms a homogenous mixture. The term insoluble is used for a pair that does not mix with each other. The solubility of a substance in a solvent depends on the “like dissolve like” principle. The polar-polar substance will mix in each other and non-polar and non-polar substance will mix each other.
Want to see the full answer?
Check out a sample textbook solutionChapter 7 Solutions
Chemistry for Today: General, Organic, and Biochemistry
- Dissolving 3.0 g of CaCl2(s) in 150.0 g of water in a calorimeter (Figure 5.12) at 22.4 °C causes the temperature to rise to 25.8 °C. What is the approximate amount of heat involved in the dissolution, assuming the specific heat of the resulting solution is 4.18 J/g °C? Is the reaction exothermic or endothermic?arrow_forwardWhat mass of a 4.00% NaOH solution by mass contains 15.0 g of NaOH?arrow_forwardCooking A cook prepares a solution for boiling by adding12.5 g of NaCl to a pot holding 0.750 L of water. Atwhat temperature should the solution in the pot boil?Use Table 14.5 for needed data.arrow_forward
- Calculate the molarity of the following solutions: a. A sample of solid Na2SO4 weighing 0.140g is dissolved in enough water to make 10.mL of solution. b. A 4.50-g sample of glucose (C6H12O6) is dissolved in enough water to give 150.mL of solution. c. A 43.5-g sample of K2SO4 is dissolved in a quantity of water, and the solution is stirred well. A 25.0-mL sample of the resulting solution is evaporated to dryness and leaves behind 2.18g of solid K2SO4.arrow_forwardWhen you heat water on a stove, small bubbles appear long before the water begins to boil. What are they? Explain why they appear.arrow_forwardFor each of the following pairs, predict which substance would be more soluble in water. a. or b. or c. orarrow_forward
- Calculate the concentration in (v/v) of the following solutions: a.250.mL of solution contains 15.0mL of acetone. b.250.mL of solution contains 15.0mL of any soluble liquid solute. c.1.0 quart of acetic acid is put into a 5- gallon container, and enough water is added to fill the container. d.A solution of acetone and water is separated by distillation. A 300.-mL sample gives 109mL of acetone.arrow_forwardIf a substance has a positive enthalpy of solution, which would likely cause more of it to dissolve, hot solvent or cold solvent? Explain.arrow_forwardMaple syrup sap is 3% sugar (sucrose) and 97% water bymass. Maple syrup is produced by heating the sap toevaporate a certain amount of the water. (a) Describe what happens to the composition and boilingpoint of the solution as evaporation takes place. (b) A rule of thumb among maple syrup producers is thatthe finished syrup should boil about 4 C higher than theoriginal sap being boiled. Explain the chemistry behindthis guideline. (c) If the finished product boils 4 C higher than the originalsap, calculate the concentration of sugar in the finalproduct. Assume that sugar is the only solute and theoperation is done at 1 atm pressure.arrow_forward
- Chemistry for Today: General, Organic, and Bioche...ChemistryISBN:9781305960060Author:Spencer L. Seager, Michael R. Slabaugh, Maren S. HansenPublisher:Cengage LearningChemistry: The Molecular ScienceChemistryISBN:9781285199047Author:John W. Moore, Conrad L. StanitskiPublisher:Cengage Learning
- Chemistry & Chemical ReactivityChemistryISBN:9781337399074Author:John C. Kotz, Paul M. Treichel, John Townsend, David TreichelPublisher:Cengage LearningChemistry & Chemical ReactivityChemistryISBN:9781133949640Author:John C. Kotz, Paul M. Treichel, John Townsend, David TreichelPublisher:Cengage LearningChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning