Concept explainers
A parabolic velocity profile was used to model flow in a laminar incompressible boundary layer in Problem 5.11. Derive the stream function for this flow field. Locate streamlines at one-quarter and one-half the total volume flow rate in the boundary layer.
5.11 A useful approximation for the .x component of velocity in an incompressible laminar boundary layer is a parabolic variation from u = 0 at the surface (y = 0) to the freestream velocity, U, at the edge of the boundary layer (y = δ). The equation for the profile is u/U = 2(y/δ) − (y/δ)2, where δ = cx1/2 and c is a constant. Show that the simplest expression for the y component of velocity is
Plot υ/U versus y/δ to find the location of the maximum value of the ratio υ/U. Evaluate the ratio where δ = 5 mm and x = 0.5 m.
Want to see the full answer?
Check out a sample textbook solutionChapter 5 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
- Consider steady, incompressible, parallel, laminar flow of a film of oil falling slowly down an infinite vertical wall. The oil film thickness is h, and gravity acts in the negative z-direction. There is no applied (forced) pressure driving the flow—the oil falls by gravity alone., except for the case in which the wall is inclined at angle ?. Generate expressions for both the pressure and velocity fields. As a check, make sure that your result agrees with that of when ? = 90°. [Hint: It is most convenient to use the (s, y, n) coordinate system with velocity components (us, ?, un), where y is into the page in Fig. Plot the dimensionless velocity profile us* versus n* for the case in which ? = 60°.]arrow_forward2. Consider the boundary-layer momentum equation for steady incompressible flow in two dimen- sions: ди dpe ду du du + po ay dx Assume the viscosity, u, to be constant. What does this equation simplifies to at a stationary solid surface? Based on this result, is a boundary layer more likely to separate in a favourable gradient (pressure decreasing) or an adverse pressure gradient? Sketch the velocity profile of a boundary layer that is attached and one that is separated. pressurearrow_forwardFrom the laminar boundary layer the velocity distributions given below, find the momentum thickness θ, boundary layer thickness δ, wall shear stress τw, skin friction coefficient Cf , and displacement thickness δ*1. A linear profile, u(x, y) = a + by 2. von K ́arm ́an’s second-order, parabolic profile,u(x, y) = a + by + cy2 3. A third-order, cubic function,u(x, y) = a + by + cy2+ dy3 4. Pohlhausen’s fourth-order, quartic profile,u(x, y) = a + by + cy2+ dy3+ ey4 5. A sinusoidal profile,u = U sin (π/2*y/δ)arrow_forward
- An incompressible viscous flow is contained between two parallel plates separated from each other by distance b. The flow is caused by the movement of the upper plate which has a velocity U, while the bottom plate is fixed. If U = 9.5 m/s and b = 3.2 cm, and there is no pressure gradient in the flow direction. a) Start with Navier-Stokes equations and determine the velocity at the point x = 7 cm and y= 0.56 cm. b) Calculate the magnitude of the vorticity at the same point. c) Calculate the rate of angular deformation at the same point. Work to 4 significant digits. Enter all values using base units or their combinations, i.e. m, m/s, Pa, N. Do not use multiples as e.g. mm, kPa. You can use values with exponents, such as 0.12e3.arrow_forwardA viscous incompressible liquid of density p and of dynamic viscosity n is carried upwards against gravity with the aid of moving side walls. This laminar flow is steady and fully developed in z-direction and there is no applied pressure gradient. The coordinate is fixed in the midway between the walls as shown below. 2d g=-gk liquid P, n x=-d x=d I. The velocity profile in z-direction is pg w(x) = (x2 – d) + U. 2n II. To be able to carry a net amount of liquid upwards, the wall velocities need to be greater than pgd²/(2n). III. If one of the walls stops, increasing the speed of the other wall to 3/2U would carry the same amount of liquid upwards. Which of the above statements are true?arrow_forwardConsider a two-dimensional flow which varies in time and is defined by the velocity field, u = 1 and v = 2yt. Compute the convective derivative of each velocity component: Du/Dt and Dv/Dt.arrow_forward
- Fluid dynamicsarrow_forwardConverging duct flow is modeled by the steady, two- dimensional velocity field V = (u, v) = (U₁ + bx) i-by. For the case in which Ug = 3.56 ft/s and b = 7.66 s¯¹, plot several streamlines from x = 0 ft to 5 ft and y=-2 ft to 2 ft. Be sure to show the direction of the streamlines. (Please upload you response/solution using the controls provided below.)arrow_forwarda) Start with Navier-Stokes equations and determine the velocity at the point x = 8.5 cm and y= 0.5 cm. Calculate velocity b) Calculate the magnitude of the vorticity at the same point. c) Calculate the rate of angular deformation at the same point.arrow_forward
- Need Solution through 15minarrow_forwardProblem 4: Differential Analysis Water flows in a thin layer between a wall and a vertical plate separated by a distance h = 1 mm. The wall is stationary while the plate moves upwards with a velocity Vplate = 1 m/s. Assume p=1000 kg/m³, v = 10-6 m²/s. 1. Assuming that the flow is laminar, steady, and fully developed, use differential analysis (Navier-Stokes) to calculate the velocity profile. 2. Calculate the flow rate per unit width. 3. Compute the Reynolds number in the water and air flow and determine if the conditions are laminar or turbulent. b-1 mm g-10 Pam Zoomed-in fully-developed region V-1 m/s Figure 4: Flow between stationary wall and moving plate.arrow_forwardAn incompressible viscous flow is contained between two parallel plates separated from each other by distance b. as shown in Figure 1. The flow is caused by the movement of the upper plate which has a velocity U, while the bottom plate is fixed. If U =7 m/s and b= 1 cm, and there is no pressure gradient in the flow direction. A.) Start with Navier-Stokes equations and determine the velocity at the point x = 3 cm and y= 0.41 cm. The value of the velocity is.B.) Calculate the magnitude of the vorticity at the same point. The magnitude value of vorticity. C.) Calculate the rate of angular deformation at the same point. The angular deformation valuearrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY