Concept explainers
(a)
The total flight time of the ball.
(a)
Answer to Problem 56AP
The total fight time of the ball is
Explanation of Solution
The initial velocity is divided into two components that is horizontal and vertical velocity component. At maximum point vertical velocity is zero for this path. The maximum height of the projectile is sixth part of the range.
Write the expression for maximum height of the ball.
Here,
Write the expression for range of the projectile path.
Substitute
Here,
Multiply equation (II) by
Multiply and divide by
The maximum height is one-sixth of range.
Substitute
Simplify the above equation.
Substitute
Simplify and rearrange the above equation as.
At peak point of the projectile path velocity along vertical direction is zero.
Write the expression for final velocity along vertical.
Here,
Initial velocity along vertical is zero.
Substitute
Rearrange the above equation.
The final velocity along vertical is
Substitute
Rearrange the above equation time to reach the peak of the path.
Here,
Substitute
Rearrange the above equation.
Write the expression for the total time of the ball’s flight.
Conclusion:
Substitute
Thus, the total flight time of the ball is
(b)
The speed of the ball at peak point.
(b)
Answer to Problem 56AP
The peak velocity at top point is
Explanation of Solution
At the peak point velocity along vertical is zero and the ball starts to accelerate under gravity in downward direction.
Write the expression for velocity at peak point.
Here,
Conclusion:
Substitute
Thus, the peak velocity at top point is
(c)
The initial vertical component of velocity.
(c)
Answer to Problem 56AP
The initial vertical component is
Explanation of Solution
Write the expression for initial vertical component of velocity.
Here,
Conclusion:
Substitute
Thus, the initial vertical component of velocity is
(d)
The initial speed of the ball.
(d)
Answer to Problem 56AP
The initial speed of the ball is
Explanation of Solution
The initial speed of the ball is given by the square root of the sum of square of horizontal and vertical velocity component.
Write the expression for initial velocity along horizontal.
Here,
Write the expression for initial velocity along vertical.
Here,
Write the expression for the initial speed of ball.
Here,
Conclusion:
Substitute
Substitute
Simplify and solve the above equation.
Thus, the initial speed of the ball is
(e)
The initial angle of the projectile.
(e)
Answer to Problem 56AP
The initial angle of projectile is
Explanation of Solution
The angle of the projectile can be given by the ratio of vertical velocity to the horizontal velocity.
Write the expression for initial angle of projectile as.
Substitute
Here,
Conclusion:
Substitute
Thus, the initial projection angle is
(f)
The greatest height with same initial speed.
(f)
Answer to Problem 56AP
The greatest height at same initial speed is
Explanation of Solution
The maximum height can be achieved by the ball at
Conclusion:
Substitute
Thus, the greatest height at same initial speed is
(g)
The maximum horizontal range.
(g)
Answer to Problem 56AP
The maximum horizontal range is
Explanation of Solution
The maximum horizontal range can be achieved at
Write the expression for maximum range as.
Here,
Conclusion:
Substitute
Thus, the maximum horizontal range is
Want to see more full solutions like this?
Chapter 4 Solutions
Physics For Scientists And Engineers With Modern Physics, 9th Edition, The Ohio State University
- Students are asked to use circular motion to measure the coefficient of static friction between two materials. They have a round turntable with a surface made from one of the materials, for which they can vary the speed of rotation. They also have a small block of mass m made from the sec- ond material. A rough sketch of the apparatus is shown in the figure below. Additionally they have equipment normally found in a physics classroom. Axis m (a) Briefly describe a procedure that would allow you to use this apparatus to calculate the coefficient of static friction, u. (b) Based on your procedure, determine how to analyze the data collected to calculate the coefficient of friction. (c) One group of students collects the following data. r (m) fm (rev/s) 0.050 1.30 0.10 0.88 0.15 0.74 0.20 0.61 0.25 0.58 i. Use the empty spaces in the table as needed to calculate quantities that would allow you to use the slope of a line graph to calculate the coefficient of friction, providing labels with…arrow_forwardPART Aarrow_forwardanswer both questionarrow_forward
- Only part A.) of the questionarrow_forwardIn general it is best to conceptualize vectors as arrows in space, and then to make calculations with them using their components. (You must first specify a coordinate system in order to find the components of each arrow.) This problem gives you some practice with the components. Let vectors A = (1,0, -3), B = (-2, 5, 1), and C = (3,1,1). Calculate the following, and express your answers as ordered triplets of values separated by commas.arrow_forwardIn general it is best to conceptualize vectors as arrows in space, and then to make calculations with them using their components. (You must first specify a coordinate system in order to find the components of each arrow.) This problem gives you some practice with the components. Let vectors A = (1,0, −3), B = (-2, 5, 1), and C = (3,1,1). Calculate the following, and express your answers as ordered triplets of values separated by commas.arrow_forward
- In general it is best to conceptualize vectors as arrows in space, and then to make calculations with them using their components. (You must first specify a coordinate system in order to find the components of each arrow.) This problem gives you some practice with the components. Let vectors A = (1,0, -3), B = (-2, 5, 1), and C = (3,1,1). Calculate the following, and express your answers as ordered triplets of values separated by commas.arrow_forwardfine the magnitude of the vector product express in sq meters what direction is the vector product in -z or +zarrow_forward4) Three point charges of magnitude Q1 = +2.0 μC, Q2 = +3.0 μС, Q3 = = +4.0 μС are located at the corners of a triangle as shown in the figure below. Assume d = 20 cm. (a) Find the resultant force vector acting on Q3. (b) Find the magnitude and direction of the force. d Q3 60° d Q1 60° 60° Q2 darrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningGlencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-HillUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningClassical Dynamics of Particles and SystemsPhysicsISBN:9780534408961Author:Stephen T. Thornton, Jerry B. MarionPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning