a. Explanation Given Information: The given values are: V T P 2 = − 0.6 , V T N 1 = 0.6 V, K n 1 =0 .2 mA / V 2 , K p 2 =1 mA / V 2 , λ 1 = λ 2 =0, R i n = 400 k Ω , I D Q 1 = 0.2 mA, I D Q 2 = 0.5 mA, V D S Q 1 = 2 V, V S D Q 2 = 3 V, V R S 1 = 0.6 V, V D D = 5 V The given circuit is shown below. Calculation: The value of source resistor of transistor 1 is R S 1 = V R S 1 I D Q 1 = 0.6 0.2 k Ω R S 1 = 3 k Ω Then drain current in the M 1 transistor, I D Q 1 = K n 1 ( V G S Q 1 − V T N 1 ) 2 0.2 × 10 − 3 = 0.2 × 10 − 3 ( V G S Q 1 − 0.6 ) 2 V G S Q 1 = 1.6 V Then drain current in the M 2 transistor, I D Q 2 = K p 2 ( V S G Q 2 + V T P 2 ) 2 0.5 × 10 − 3 = 1 × 10 − 3 ( V S G Q 2 − 0.6 ) 2 V S G Q 2 = 1.307 V The gate voltage of the M 1 transistor is V G 1 = V R S 1 + V G S Q 1 = 0 b. To determine The small-signal voltage gain of the given circuit.

MICROELECT. CIRCUIT ANALYSIS&DESIGN (LL)

4th Edition

ISBN: 9781266368622

Author: NEAMEN

Publisher: MCG

See similar textbooks

Question

Chapter 4, Problem 4.68P

To determine

The design parameters of a multistage transistor circuit to meet the specifications.

To determine

The small-signal voltage gain of the given circuit.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4, Problem 4.67P

Chapter 4, Problem 4.69P

Students have asked these similar questions

A Three-phase, 3.3 kV, Y connected, 500 kVA, 16 salient pole rotor alternator. The direct and quadrature axis synchronous reactance are 8 and 50/ph respectively. The machine is supplying a load of 350 kVA at 0.8 power factor lagging, Determine: 1. Power angle. 2. Percentage Voltage regulation. 3. Developed power. 4. Reluctance power

A Three-phase, 12 pole, Y-connected alternator has 108 slots and 14 conductors per slot. The windings are (5/6th) pitched. The flux per pole is 57 mWb distributed sinusoidally over the pole. If the machine runs at 500 r.p.m., determine the following: (a) The frequency of the generated e.m.f., (b) The distribution factor, (c) The pitch factor, and (d) The phase and line values of the generated e.m.f.?

Many machines, such as lathes, milling machines, and grinders, are equipped with tracers to reproduce the contours of templates. The figure is a schematic diagram of a hydraulic tracer in which the tool duplicates the shape of the template on the workpiece. a) Explain how the system works. b) Draw a block diagram and identify the system's elements. c) Classify the control system. Oil under pressure Template Style Tool Piece of work

Chapter 4 Solutions

MICROELECT. CIRCUIT ANALYSIS&DESIGN (LL)

Ch. 4 - Prob. 4.1EP Ch. 4 - For the circuit shown in Figure 4.1, VDD=3.3V and...Ch. 4 - Prob. 4.1TYU Ch. 4 - For the circuit shown in Figure 4.1, VDD=3.3V and...Ch. 4 - For the circuit in Figure 4.1, the circuit and...Ch. 4 - The parameters for the circuit in Figure 4.8 are...Ch. 4 - A transistor has the same parameters as those...Ch. 4 - The parameters of the circuit shown in Figure 4.14...Ch. 4 - Consider the circuit shown in Figure 4.14. Assume...Ch. 4 - For the circuit shown in Figure 4.19, the...

Knowledge Booster

The design parameters of a multistage transistor circuit to meet the specifications.

Solution Summary: The author explains the design parameters of a multistage transistor circuit to meet the specifications.

The design parameters of a multistage transistor circuit to meet the specifications.

The small-signal voltage gain of the given circuit.

Want to see the full answer?

Chapter 4 Solutions