1. In the following closed-loop system, a PD controller of the form K(s + 5) is used. Design the gain K suchthat the system achieves an overshoot of 16%. Calculate the settling time and peak time for the PDcontrolled system.CompensatorR(s) +E(s)Plant1C(s)K(s+Zc)(s+1)(s+2)(s+5)

Answered: Image /qna-images/answer/0b28847e-41d0-4d0f-b00c-a0928715a2bc.jpg

Answered: 1. In the following closed-loop system,…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Similar questions

Q2 Figure Q2 shows a Linear Feedback Shift Register circuit. Write down the VHDL entity associated with a 6-bit shift register with the inputs and outputs as shown in Figure Q2. (a) (b) Write down a VHDL architecture for a 6-bit shift register. 6-bit parallel out shift register clk d reset serial_in Figure Q2
ii. Describe the role of the process reaction curve ( Figure 3 )and the Ziegler-Nichols PID tuning rules (Table 1) in control system design. Tangent line at inflection point Figure 3 Table: 1 Zeigler-Nichols PID controller Tuning rules Type of Controller K, T T P. 00 0.95 125 PI 0.3 PID 2L 0.5L Imnortant Note:
1 - Analyse the circuit as shown in Figure (initial state is 15) 2- show the timing diagram and determine the module (initial state is 15), Provide analysis process. CLK Jo FFO C Ko FF1 de Q₁ K₁ ģ FF2 J₂ Q₂ K₂ Q₂ FF3 J₂ C K3 Q3 18 Q₂0
Q2) For a single phase (ac to ac) voltage controller, if the input supply voltage is (250Sin314t) with frequency (50 Hz) and the load is (R=5 Q). Draw the controller circuit, and then do the followings: - a. Determine the rms value of the output voltage at firing angle (a=60 ). b. Determine the value of (a) in order to obtain output voltage of (70.7 V).
Hybrid vehicle. FIGURE P1 shows the block diagram of a possible cascade control scheme for an HEV driven by a dc motor (Preitl, 2007). The block diagram of the speed control of an HEV taken from FIGURE P1, and rearranged as a unity feedback system is shown in FIGURE P2. Here the system output is C(s) = Kss V(s), the output voltage of the speed sensor/transducer. pC, Av,- Speed K, Gre(s) controller command Torque Amplifier controller output & power voltage amplifier Acro- Motive dynamie Armature Speed |drag torque Angular speed, Ref. circuit Armature torque Vehicle signal R,(s). error U(s) T(s)T,(s) current E,(s) speed, V(s) Gse(s) K, Grc(s) R. tot Friction Feedback speed signal Kss2(s) Feedback torque current signal Kes I(S) T,(s) E,(s) Back emf D=k ks Current sensor sensitivity Kcs Speed sensor sensitivity Kss FIGURE P1 Hybrid Vehicle R (s), E (s) Uc(s) |C(s) + Gsc(s) 0.11 (s + 0.6) SC s (s + 0.5173) + 5 (s + 0.6) (s + 0.01908) URE P2 Block diagram of the speed control of an HEV a.…
1.a. In a DC servo motor system, the tachometer feeds back a voltage that’s proportional to motor speed.Where does this voltage go to?A. The interpolator cardB. The CPU in the main controllerC. The driverD. The axis logic card1.b. A type of feedback device that uses a rotor and senses the position of the motor by means of sine andcosine waveforms is called a/anA. tachometer.B. encoder.C. resolver.D. alternator.
(c) The block diagram of a system, with proportional controllers implemented in the primary and secondary loops of a cascade control implementation, is given in Figure Q1c. R+ Ka K 55+1 (5+1Xos+1) Figure Q1c Kez is designed so that the time constant of the secondary loop is 0.5 seconds. (i) Determine Kc2. (ii) Determine the ultimate gain of the primary controller.
What is min,typ and max?
A temperature control system operates by sensing the difference between the thermostat setting and the actual temperature and then opening a fuel valve an amount proportional to this difference. Draw a functional closed-loop block diagram identifying the input and output transducers, the controller, and the plant. Further, identify the input and output signals of all subsystems previously described.
I need help on this asap:
A/D CONVERTER( NEED NEAT EXPLANATION HANDWRITTEN SOLUTION ONLY PLEASE OTHERWISE DOWNVOTE).
c. Sketch the zero-pole plot and the direct form II diagram of the completed design out of part b. d. Calculate and sketch the output sequence after feeding x [n] into this system.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning