For a single phase (ac to ac) voltage controller, if the input supply voltage is (250Sin314t) with frequency (50 Hz) and the load is (R=5 N). Draw the controller circuit, and then do the followings: - a. Determine the rms value of the output voltage at firing angle (a=60 ). b. Determine the value of (a) in order to obtain output voltage of (70.7 V).

For a single phase (ac to ac) voltage controller, if the input supply voltage is (250Sin314t) with frequency (50 Hz) and the load is (R=5 N). Draw the controller circuit, and then do the followings: - a. Determine the rms value of the output voltage at firing angle (a=60 ). b. Determine the value of (a) in order to obtain output voltage of (70.7 V).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5. Draw the circuit diagram, input and output voltage waveforms of a phase controlled, single phase AC-AC voltage controller for a firing angle, a=90 degree.
Design a single phase AC voltage controller which has supply voltage of 120, Vrms and 60 Hz. The output power the the circuit is 500 W. Determine the total harmonics distortion for the current (THDI). Your THDI must be lower than 10%.
Idk 8. A single-phase fully controlled, full-wave, bridge rectifier has a source of 230 V rms at 50 Hz, and is feeding a load R=25 and L= 10 mH. The firing angle a = 45° and the current extinction angle B=230°. It is required to: (a) Sketch the appropriate load voltage and load current waveforms. (b) Determine whether the current is continuous or discontinuous. (d) Determine the average load voltage and current. (e) Determine the rms load voltage and current. (f) Determine the a.c. and d.c powers absorbed by the load. (g) Determine the efficiency of the converter.
A three phase fullwave controlled rectifier has an input voltage which is 480vrmsat 60hz. the load modelled as a series resistance and inductance with R=10ohm and l=50mH. determine the delay angle to produce an average of 50ain the load.
Consider the full-wave bridge rectifier circuit. The input signal is 120 V (rms) at 60 Hz. The load resistance is R250. The peak output voltage is to be 9 V and the ripple voltage is to be no more than 5 percent. Determine the required turns ratio and the load current. Note: please solve within 30 minutes. Avoid plagiarism.
QUESTION 3 a) In order to drive a DC motor, a square wave signal as shown in Figure Q3(a) is required. Due to cost factor, a 555 timer chip will be used for this purpose. i. Develop the timer circuit and calculate resistors R1 and R2, and the capacitor Cext in order to produce the signal. Draw and label the circuit. ii. Describe the effect of changes in (a) duty cycle and (b) frequency of the signal on the motion of the DC motor . 1 1.25 2.25 2.5 3.5 3.75 4.75 5 ms ms ms ms ms ms ms ms ms Figure Q3(a)
For a single-phase half-wave centre-tapped rectifier, the fundamental frequency of output voltage is__ e) two times the input frequency. f) three times the input frequency. g) same the input frequency. h) four times the input frequency.
(A):- For the circuit shown in Figure (2). 1) Determine IBQ, Icqand VCEQ- 12 V 2) Draw the dc load line. 22 kn 3) Calculate the stability factor Svr 220 LQ B-60 -40 ka
A three phase full wave rectifier is shown below along with the peak input phase voltage Vm=169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is Vpc=280.7V and. The RMS transformer secondary current is equal to 81.72A, the output RMS voltage is equal to VRMS=280.93V and the output resistance is equal to 2.8070. The TUF would be equal to: Secondary a平a字a辛 R 太D。太D。太D. Select one: 0.875 Ob. 0.955 O C. 0.551 O d. 0.432 Compared with power transistors, thyristors have the following characteristic
Explain the operation of a full-wave voltage quadrupler circuit (With proper explanation, equation, and diagram of each cycle).
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
Compute the dc load voltage of a SCR full-wave control circuit if the firing angle is 36 degree. Assume resistive load RL=10 ohms with supply of 220V, 60Hz. A. 63.3V B. 89.6V C. 126.7V D. 179.2V (c)