NO AI PLEASE The diff-amp in the following figure has parametersV+3 V, V = -3 V, and IQ = 0.18 mA. The transistorparameters are VTN = 0.35 V, kn=100μA/V², WL = 4,and = 0. Determine RD such that the maximumvalue of the common-mode input voltage is Vcm (max)= 2.25 V. The input transistors M1 and M2 mustremain biased in the saturation region.V+wwRpwwRDVD2VcmM₁M2

Answered: Image /qna-images/answer/2b16c5f7-871f-448a-a6f4-60478b8de4f0.jpg

Answered: The diff-amp in the following figure…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.11MCQ

See similar textbooks

Similar questions

circuits by using the small signal models of the transistor. Assume the Early voltage of the transistors are infinitely large. Calculate the small-signal input and output impedances of the following Vcc R1 R1 Rout VB RE Rin R2
The n-channel JFET and the D-MOSFET have very similar I-V output characteristics. Which of these two structures can be operated in enhancement mode and why is that possible.
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
4) Consider the clamping circuit below, assume Vref=3 V and Vin=5sin(wt) ..Draw the output voltage waveform. Clearly mark the max and min of the voltage.. Vref
The transistor parameters for the circuit in Figure are B, =B2 = 100, VBE1on) = VBE2ton) = 0.7 V, and %3D VA1 =VA2 =0.Find the small signal voltage gain Av = vo/vs. (Note that V-=0.026 V) Vcc=9 V Rib Q1 Vs 1 ko -Ro 20 V 100 Q -ww
The DC Current Gain of a Transistor is Select one: a. Ratio of Collector Current to Base Current b. Ratio of Base Current to Collector Current c. Ratio of Emitter Current to Collector Current d. Ratio of Base Current to Emitter Current
II.The following figure shows a class AB amplifier. (a) Determine the parameters of dc VB (Q1), VB (Q2), VE, ICQ, VCEQ (Q1), VCEQ (Q2). (b) For a 5-Vrms input, determine the power that is provided to the load resistor, and (c) Draw the output signal +Vcc +9 V 1.0kn D: R 5.0 V rms R2 10 kN -Vec
A single stage amplifoer has a single stage of 60. The collector load of 500 ohms and the input impedance is 1kilo ohms. Calculate the overall gain when two such stages are cascaded through R-C coupling.
Please solve with work shown. Will upvote
1. A certain phototransistor has a BDC. 150. If I = 250, what is the collector current? 2. In the figure below, if Vcc is replaced from a 12-V to an 18-V source. what would be output voltage when (a) the light source is OFF and (b) when the light source is ON. #12 V
which of the following configurations has low impedance and high output impedance? a. common-base. c. common-collector. b. common-emitter. d. all of these.
Determine VB, VE, VC, VCE, IB, IE, and IC in Figure. The 2N3904 is a general purpose transistor with a typical BDC 200 Vcc +30 V WWII VCE VB R₁ • 22 ΚΩ IC(mA) Chọn... * Chọn... * IB(UA) Chọn... * IE(MA) Chọn... ◆ Chọn... * Chọn... * Chọn... * VE VC R₂ ´ 10 ΚΩ www Rc 1.0 ΚΩ 2N3904 PDC=200 RE 1.0 ΚΩ

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning