Suppose you have three push buttons connected to (B5, B6 & B7) and eight LED's connected to (DoD7): Write a program to flash ON the odd LED's if we press the switch B7 for 0.4s, flash ON the evenLED's if we press the switch (B6 for 0.4s and flash ON all the LED's if we press the switch B5 for 0.7s.

Programming Logic (Conceptual Outline)We'll need a microcontroller (like an Arduino or similar) to…

Answered: Suppose you have three push buttons…

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 30RQ

See similar textbooks

Similar questions

2-A) What's the name of the opamp circuit below? Briefly explain the logic. 2-B) Why is there a DC 1 volt offset in Vs sine signal?
Design a circuit that controls the passage of a signal "A" with the specifications: 1. Output X will equal A when control B and C are the same 2. X will remain HIGH when B and C are different. Hint: Set "A" input as a CLK pin.
Design*/draw a 10-second timer using a 555 IC (Astable) with correct values of R1-2 and C. and an LED to flash For the output (pin 3), connect an LED and current limiting resistor (220 Omhs ) to the ground. Assume 50% DC and select a Capacitor;
Draw a 2x1 multiplexer block diagram.Create the status table. Find the simplest form of circuit output with Karnaugh.Explain the circuit problem that may occur.What should be done to fix the problem?(NEED A NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE)
Explain and draw an NPN transistor chip in a circuit of your own design. I want the actual chips drawn with the symbols inside, then a wiring diagram showing the interconnections. Power source and A, B, C, and/or D inputs may be added in the form of either buttons or switches.
ASYNCIN Dan Synchronous System CLOCK Figure Q4 (b) The circuit in Figure Q4 (c) consists of edge triggered flipflops. The second flipflop receives the clock signal through a long slow path which results in delay. Answer the following questions: Q1 Q2 IN DaK CLOCKD CLK CLOCK A long, slow path Figure Q4 (c) 林 Define clock skew, Explain with a timing diagram, what problem this circuit might face? What condition it must satisfy to ensure that the intended circuit output is not affected? For the following LFSR circuit in the Figure Q4 (d), let the initial entries of stages R, be S, for 0sisn. Compute the first 12 bit output for the following cases of initial entries: (d) S2 Si So Case 1 Study Pack Practice &A Case 2
Q3. A door sensor is connected to P0.5 pin, an LED to P1.5 pin and a buzzer to P2.5 pin. Write an 8051 C program to monitor the door sensor such that when it is opened, the LED will blink and the buzzer will sound every 500ms, otherwise, when the door is closed, both of the LED and buzzer will be OFF.
i need the answer quickly
Choose the true H-bridge motor statements in the list below. O The L298N has a PWM input signal that can be used to control the motor direction. (false, it controls the speed of the motor. O You should always transition through the "Off" state when changing direction with the H-bridge. O The H-bridge provides a means of controlling a motors spin direction. O If all four H-bridge switches are open, the motors will spin. O The H-bridge uses four switches to control the current flow.
Here is the data flow diagram for a particular instruction. The various values shown indicate the state of the machine after the action of this instruction. GatePC DR 101 GateMARMUX RO OnFFFO OxFFFE PC X RI MARMUX TRAPVECTOR R2 OxFFFD X:0:0 PCMUX R3 OFFFB EXT R4 ODFFA OFFSET6 OR R5 OXFFFD PCOFPSET PC OR BASER R6 OcFFFC (7:0) R7 OscOFO8 ADDR2MUX ADDRIMUX SR2 SRI 010 [100] SEXT IMMS (8:0) SEXT SEXT FINITE SRZMUX [50] SEXT STATE [4:0| 2 MACHINE Arith/Logic Operation AL select A/L RESULT LOGIC GateALU Gate MDR 16 MDR MAR 16 OUTPUT INPUT MEMORY XFE02 XFE06 What is that instruction in binary? (You may use any number of spaces to organize the bits.) address instruction x3002
Explain and draw a 7490 chip in a circuit of your own design. I want the actual chips drawn with the symbols inside, then a wiring diagram showing the interconnections. Power source and A, B, C, and/or D inputs may be added in the form of either buttons or switches.
please type so that i can read your solution

SEE MORE QUESTIONS

Recommended textbooks for you

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning