Concept explainers
The flow velocity along the floor and location of the maximum speed in the flow field.
Answer to Problem 112P
The flow speed along the floor is
The location of the maximum velocity is
Explanation of Solution
Given information:
The velocity component along the x direction is
Write the expression for the velocity component along x direction.
Here, the distance of the attachment above the floor is
Write the expression for the velocity component along y direction.
The flow is assumed to be steady and incompressible.
Write the expression for the maximum speed along x direction.
Calculation:
Substitute
Therefore, the flow speed along the floor is
Substitute
Substitute
Substitute
Substitute
At the origin, the velocity components are zero thus, the vacuum cleaner is not good at the origin.
Conclusion:
The flow speed along the floor is
The location of the maximum velocity is
Want to see more full solutions like this?
Chapter 4 Solutions
Fluid Mechanics: Fundamentals and Applications
- he velocity at apoint in aflued for one-dimensional Plow wmay be aiven in The Eutkerian coordinater by U=Ax+ Bt, Show That X Coordinates Canbe obtained from The Eulerian system. The intial position by Xo and The intial time to zo man be assumeal · 1. x = foxo, yo) in The Lagrange of The fluid parficle is designatedarrow_forwardFrom the question he has wrote the given infomation. i dont understand how he has got that from the questionarrow_forwardhello, can you do a step by step solution with explaination for me thank you so mucharrow_forward
- I got an answer of x = 89.4mm And a reynolds number of 1.09 * 10^5 Just want to confirm my matharrow_forwardPlease also explain.arrow_forwardThe entrance flow between two parallel plates (gap h) has a velocity that varies linearly at the entrance and develops into a fully parabolic profile at the exit. What is the relationship between the maximum velocity at the entrance and that at the exit? You can show by symmetry that the maximum velocity is attained at the mid-plane between the two plates.arrow_forward
- Engine oil at 60°C rotates as a rigid body about the z-axis in a spinning cylindrical container. There are no viscous stresses since the water moves as a solid body; thus the Euler equation is appropriate. (We neglect viscous stresses caused by air acting on the water surface.) Integrate the Euler equation to generate an expression for pressure as a function of r and z everywhere in the water. Write an equation for the shape of the free surface (zsurface as a function of r). (Hint: P = Patm everywhere on the free surface. The flow is rotationally symmetric about the z-axis.)arrow_forwardPravin bhaiarrow_forwardConsider two-dimensional flow in the x-y plane where we are using polar coordinatesr and O to describe the motion. We will call u the radial velocity and v the azimuthal velocity (see figure below). y u Xarrow_forward
- EXAMPLE 6-4 Water Jet Striking a Stationary Plate Water is accelerated by a nozzle to an average speed of 20 m/s, and strikes a stationary vertical plate at a rate of 10 kg/s with a normal velocity of 20 m/s (Fig. 6-22). After the strike, the water stream splatters off in all directions in the plane of the plate. Determine the force needed to prevent the plate from moving horizontally due to the water stream. P atm CV Z X Out F FRarrow_forwardHello sir Muttalibi is a step solution in detailing mathematics the same as an existing step solution EXAMPLE 6-1 Momentum-Flux Correction Factor for Laminar Pipe Flow CV Vavg Consider laminar flow through a very long straight section of round pipe. It is shown in Chap. 8 that the velocity profile through a cross-sectional area of the pipe is parabolic (Fig. 6-15), with the axial velocity component given by r4 V R V = 2V 1 avg R2 (1) where R is the radius of the inner wall of the pipe and Vavg is the average velocity. Calculate the momentum-flux correction factor through a cross sec- tion of the pipe for the case in which the pipe flow represents an outlet of the control volume, as sketched in Fig. 6-15. Assumptions 1 The flow is incompressible and steady. 2 The control volume slices through the pipe normal to the pipe axis, as sketched in Fig. 6-15. Analysis We substitute the given velocity profile for V in Eq. 6-24 and inte- grate, noting that dA, = 2ar dr, FIGURE 6–15 %3D Velocity…arrow_forwardWhat is the definition of a pathline? What do pathlines indicate?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY