Concept explainers
Determine the specific volume of superheated water vapor at 3.5 MPa and 450°C based on (a) the ideal-gas equation, (b) the generalized compressibility chart, and (c) the steam tables. Determine the error involved in the first two cases.
(a)
The specific volume of superheated water vapour based on the ideal gas equation.
The error involved.
Answer to Problem 86P
The specific volume of superheated water vapour based on the ideal gas equation is
The error involved is
Explanation of Solution
Write the equation of specific volume of superheated water using ideal gas equation of state.
Here, gas constant is R, pressure and temperature of R-134a are P and T respectively.
Calculate the percentage of error involved.
Here, specific volume at pressure and temperature of 3.5 MPa and
Conclusion:
Refer to Table A-1, obtain the gas constant, R of water as
Substitute
Thus, the specific volume of superheated water vapour based on the ideal gas equation is
Refer to Table A-6, obtain the value of
Substitute
Thus, the error involved is
(b)
The specific volume of superheated water vapour based on the generalized compressibility chart.
The error involved.
Answer to Problem 86P
The specific volume of superheated water vapour based on the generalized compressibility chart is
The error involved is
Explanation of Solution
Calculate the reduced pressure.
Here, pressure of superheated water vapour is P and critical pressure is
Calculate the reduced temperature.
Here, temperature of superheated water vapor is T and critical temperature is
Calculate the specific volume of superheated water vapour based on the generalized compressibility chart.
Here, the specific volume at ideal condition is
Conclusion:
Refer to Table A-1, obtain the critical pressure and critical temperature of water.
Substitute 22.06 MPa for
Substitute 647.1 K for
Refer to figure A-15, “The compressibility chart”, obtain the compressibility factor, Z by reading the calculated reduced pressure and reduced temperature as 0.961.
Substitute 0.961 for Z and
Thus, the specific volume of superheated water vapour based on the generalized compressibility chart is
Substitute
Thus, the error involved is
(c)
The specific volume of superheated water vapour based on the data from tables.
Answer to Problem 86P
The specific volume of superheated water vapour based on the data from table is
Explanation of Solution
Refer to Table A-6, obtain the specific volume at pressure and temperature of 3.5 MPa and
Thus, the specific volume of superheated water vapour based on data from steam tables is
Want to see more full solutions like this?
Chapter 3 Solutions
Thermodynamics: An Engineering Approach
- 2. Link BD consists of a single bar 1 in. wide and 0.5 in. thick. Knowing that each pin has a in. diameter, determine (a) the maximum value of the normal stress in link BD and the bearing stress in link BD if 0 = 0, (b) the maximum value of the normal stress in link BD if 0 = 90. -6 in.- 12 in. 30° D 4 kipsarrow_forwardIn the image is a right rectangular pyramid of total mass m. Note the location of point Q. Determine the inertia dyadic for the pyramid P, relative to point Q for e hat unit vectors.arrow_forwardauto controlsarrow_forward
- auto controlsarrow_forwardA 4 ft 300 Ib 1000 Ib.ft 350 Ib C 2 ft 3. 45° 250 Ib B. 3ft B 25ft 200 Ib 150 Ib Replace the force system acting on the frame shown in the figure by a resultant force (magnitude and direction), and specify where its line of action intersects member (AB), measured from point (A).arrow_forwardCan you research the standard percentage of Steam Quality in:(1.) Boiler - leaving boilerBoiler -> Out(2.) Condenser - coming in condenser In -> CondenserProvide reference Also define: steam quality, its purpose and importancearrow_forward
- Numbers 1 and 2 and 5 are are optional problems. However, I only need the values (with units) of 3, 4 and 6. Thank you :)arrow_forwardThree cables are pulling on a ring located at the origin, as shown in the diagram below. FA is 200 N in magnitude with a transverse angle of 30° and an azimuth angle of 140°. FB is 240 N in magnitude with coordinate direction angles α = 135° and β = 45°. Determine the magnitude and direction of FC so that the resultant of all 3 force vectors lies on the z-axis and has a magnitude of 300 N. Specify the direction of FC using its coordinate direction angles.arrow_forwardturbomachieneryarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY