DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 35, Problem 22RQ
Why is it possible for the fusion zone to have a chemistry that is different from the filler metal?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
4. why Filler metals are used in fusion welding process?
What are the possible defects of MIG welding on stainless steels?
3) The dihedral wetting angle between solid-
liquid interface with lowest solidification
cracking tendency under identical welding
conditions is
0°
O45°
60°
90°
Chapter 35 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 35 - What types of design features favor manufacture as...Ch. 35 - What types of manufacturing processes fall under...Ch. 35 - Define welding.Ch. 35 - What conditions are required to produce an ideal...Ch. 35 - What are some of the ways in which welding...Ch. 35 - What are some possible problems associated with...Ch. 35 - What are the three primary aspects required to...Ch. 35 - How are welding processes identified by the...Ch. 35 - What is thermal cutting?Ch. 35 - What are some of the common types of weld defects?
Ch. 35 - What are the four basic types of fusion welds?Ch. 35 - What are some of the common edge configurations...Ch. 35 - What is the role of an insert in welding?Ch. 35 - What types of weld joints commonly employ fillet...Ch. 35 - What are the five basic joint tvpes for fusion...Ch. 35 - What are some of the factors that influence the...Ch. 35 - Why is it important to consider welded products as...Ch. 35 - How does the fracture resistance and temperature...Ch. 35 - How might excessive rigidity actually be a...Ch. 35 - What is autogenous welding?Ch. 35 - In what way is the weld-pool segment of a fusion...Ch. 35 - Why is it possible for the fusion zone to have a...Ch. 35 - Why is it not uncommon for the selected filler...Ch. 35 - What are some of the defects or problems that can...Ch. 35 - Why can the material properties vary widely within...Ch. 35 - What are some of the structure and property...Ch. 35 - Why do most welding failures occur in the...Ch. 35 - Discuss the various regions within the...Ch. 35 - What are some of the characteristics and...Ch. 35 - What process features can increase the size of the...Ch. 35 - What are some of the difficulties or limitations...Ch. 35 - What is the purpose of pre- and postheating in...Ch. 35 - What heat-related metallurgical effects can...Ch. 35 - What causes weld-induced residual stresses?Ch. 35 - What is the cause of reaction-type residual...Ch. 35 - How are reaction stresses affected by the distance...Ch. 35 - What are some of the techniques that can reduce...Ch. 35 - How can the surfaces of weldments be put into...Ch. 35 - In what ways might welding create geometric...Ch. 35 - 40. Why might a welded structure warp if the...Ch. 35 - Why might a stress relief heat treatment be...Ch. 35 - What are some of the techniques that can be...Ch. 35 - Why are the terms weldability and joinability...Ch. 35 - Prob. 1PCh. 35 - Two pieces of AISI 1025 steel are being...Ch. 35 - Figure 35.A schematically depicts the design of a...Ch. 35 - Investigate and summarize some of the important...Ch. 35 - What do you foresee as the major difficulties when...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
determine the magnitude of F and its direction . Prob. F2-10
Engineering Mechanics: Statics
Determine the width b if the height h=2b.
Mechanics of Materials (10th Edition)
Assume the support at B is a roller. Point C is located just to the right of the 8-kip load. Prob. 7-2
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
1.7 A level scaffold s to be supported at the center of a 12–ft ladder, as shown. Determine the required length...
Applied Statics and Strength of Materials (6th Edition)
Repeat Problem 1.54 if the flow inside the apparatus is liquid water (=1000kg/m3) instead of air. Find the pres...
Fundamentals Of Thermodynamics
The design condition for a space is 77 F (25 C) db and 50 percent relative humidity with 55 F (13 C) db supply ...
Heating Ventilating and Air Conditioning: Analysis and Design
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What problems can occur to stainless steel as it is allowed to form carbide precipitation during welding?arrow_forwardWhy is the formation of martensite a problem when welding on high carbon steels?arrow_forwardWhy would some low-carbon steels have severe porosity when welded with the GTA welding process?arrow_forward
- Referring to Figure 26-20, what would the preheat temperature range be for an iron-carbon alloy with carbon?arrow_forwardWelding stainless steel is a complicated process because (uniform / intergranular / erosion) corrosion may happen, to avoid this issue post-weld-heat treatment is conducted to (precipitate / dissolve) carbide particles.arrow_forwardList five advantages of the modulated current andpulsed-arc metal transfer process.arrow_forward
- A manufacturer wants to produce a weld batch with the eutectic composition. It has 250 kg of electric weld scrap with 60% p Sn-40% p Pb and 1,250 kg of plumbing weld scrap with 60% p Pb40% p Sn. If all the scrap is melted, how much of each metal needs to be added to achieve the desired composition? Consider the lead-tin phase diagram.arrow_forwardnormalizing advantages over quenching (heat treatment process)arrow_forwardI need the answer as soon as possiblearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY