DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 35, Problem 32RQ
What is the purpose of pre- and postheating in welding operations?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
8) The correct ways to control liquation
cracking tendency in fusion weld joint are
I.
Use of filler metal that solidifies before the
partially melted zone
I.
Use of single pass welding with higher net heat
input instead of multipass welding
III. Use of high energy density processes
IV. Preheating the substrates
V.
Use of base metals with fine grain structure
OI, II, and III
II, and IV
OII, IV, and V
O II, III and IV
What are the disadvantages of MIG welding on stainless steels?
??
Chapter 35 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 35 - What types of design features favor manufacture as...Ch. 35 - What types of manufacturing processes fall under...Ch. 35 - Define welding.Ch. 35 - What conditions are required to produce an ideal...Ch. 35 - What are some of the ways in which welding...Ch. 35 - What are some possible problems associated with...Ch. 35 - What are the three primary aspects required to...Ch. 35 - How are welding processes identified by the...Ch. 35 - What is thermal cutting?Ch. 35 - What are some of the common types of weld defects?
Ch. 35 - What are the four basic types of fusion welds?Ch. 35 - What are some of the common edge configurations...Ch. 35 - What is the role of an insert in welding?Ch. 35 - What types of weld joints commonly employ fillet...Ch. 35 - What are the five basic joint tvpes for fusion...Ch. 35 - What are some of the factors that influence the...Ch. 35 - Why is it important to consider welded products as...Ch. 35 - How does the fracture resistance and temperature...Ch. 35 - How might excessive rigidity actually be a...Ch. 35 - What is autogenous welding?Ch. 35 - In what way is the weld-pool segment of a fusion...Ch. 35 - Why is it possible for the fusion zone to have a...Ch. 35 - Why is it not uncommon for the selected filler...Ch. 35 - What are some of the defects or problems that can...Ch. 35 - Why can the material properties vary widely within...Ch. 35 - What are some of the structure and property...Ch. 35 - Why do most welding failures occur in the...Ch. 35 - Discuss the various regions within the...Ch. 35 - What are some of the characteristics and...Ch. 35 - What process features can increase the size of the...Ch. 35 - What are some of the difficulties or limitations...Ch. 35 - What is the purpose of pre- and postheating in...Ch. 35 - What heat-related metallurgical effects can...Ch. 35 - What causes weld-induced residual stresses?Ch. 35 - What is the cause of reaction-type residual...Ch. 35 - How are reaction stresses affected by the distance...Ch. 35 - What are some of the techniques that can reduce...Ch. 35 - How can the surfaces of weldments be put into...Ch. 35 - In what ways might welding create geometric...Ch. 35 - 40. Why might a welded structure warp if the...Ch. 35 - Why might a stress relief heat treatment be...Ch. 35 - What are some of the techniques that can be...Ch. 35 - Why are the terms weldability and joinability...Ch. 35 - Prob. 1PCh. 35 - Two pieces of AISI 1025 steel are being...Ch. 35 - Figure 35.A schematically depicts the design of a...Ch. 35 - Investigate and summarize some of the important...Ch. 35 - What do you foresee as the major difficulties when...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Determine the angle between the two cables attached to the pipe.
Engineering Mechanics: Statics
The zero force members in the truss.
Engineering Mechanics: Statics & Dynamics (14th Edition)
A space is at a temperature of 75 F (24 C), and the relative humidity is 45 percent. Find (a) the partial press...
Heating Ventilating and Air Conditioning: Analysis and Design
The cylinder volume below the constant loaded piston has two compartments, A and B, filled with water, as shown...
Fundamentals Of Thermodynamics
7.9 The U-shaped but-op section shown is composed of dressed (S4S) timber sections. (See Appendix E for dress...
Applied Statics and Strength of Materials (6th Edition)
12. Consider the following strange, but true, units:
1 arroba =11.5 kilograms [kg] 1 peck = 9 liters [L]
A bask...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What term describes the fusion or growing together of the grain structure of the materials being welded?arrow_forwardWhat brazing or soldering process uses a machine similar to a spot welder to produce the heat required to make a joint?arrow_forwardWhat effect does shortening the electrode extension have on weld penetration?arrow_forward
- Which SMA welding electrodes are commonly used to weld on sheet metal fabrications?arrow_forwardHow long does it take the weld metal to go through its thermal cycle during a weld?arrow_forwardReferring to Table 27-2, what commercial joining process can be used to braze sheet stainless steel?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY