DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 35, Problem 35RQ
What is the cause of reaction-type residual stresses?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What is the dynamic stress?
What is the reaction force?
What happens to the shear stress as flexural capacity increases?
Chapter 35 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 35 - What types of design features favor manufacture as...Ch. 35 - What types of manufacturing processes fall under...Ch. 35 - Define welding.Ch. 35 - What conditions are required to produce an ideal...Ch. 35 - What are some of the ways in which welding...Ch. 35 - What are some possible problems associated with...Ch. 35 - What are the three primary aspects required to...Ch. 35 - How are welding processes identified by the...Ch. 35 - What is thermal cutting?Ch. 35 - What are some of the common types of weld defects?
Ch. 35 - What are the four basic types of fusion welds?Ch. 35 - What are some of the common edge configurations...Ch. 35 - What is the role of an insert in welding?Ch. 35 - What types of weld joints commonly employ fillet...Ch. 35 - What are the five basic joint tvpes for fusion...Ch. 35 - What are some of the factors that influence the...Ch. 35 - Why is it important to consider welded products as...Ch. 35 - How does the fracture resistance and temperature...Ch. 35 - How might excessive rigidity actually be a...Ch. 35 - What is autogenous welding?Ch. 35 - In what way is the weld-pool segment of a fusion...Ch. 35 - Why is it possible for the fusion zone to have a...Ch. 35 - Why is it not uncommon for the selected filler...Ch. 35 - What are some of the defects or problems that can...Ch. 35 - Why can the material properties vary widely within...Ch. 35 - What are some of the structure and property...Ch. 35 - Why do most welding failures occur in the...Ch. 35 - Discuss the various regions within the...Ch. 35 - What are some of the characteristics and...Ch. 35 - What process features can increase the size of the...Ch. 35 - What are some of the difficulties or limitations...Ch. 35 - What is the purpose of pre- and postheating in...Ch. 35 - What heat-related metallurgical effects can...Ch. 35 - What causes weld-induced residual stresses?Ch. 35 - What is the cause of reaction-type residual...Ch. 35 - How are reaction stresses affected by the distance...Ch. 35 - What are some of the techniques that can reduce...Ch. 35 - How can the surfaces of weldments be put into...Ch. 35 - In what ways might welding create geometric...Ch. 35 - 40. Why might a welded structure warp if the...Ch. 35 - Why might a stress relief heat treatment be...Ch. 35 - What are some of the techniques that can be...Ch. 35 - Why are the terms weldability and joinability...Ch. 35 - Prob. 1PCh. 35 - Two pieces of AISI 1025 steel are being...Ch. 35 - Figure 35.A schematically depicts the design of a...Ch. 35 - Investigate and summarize some of the important...Ch. 35 - What do you foresee as the major difficulties when...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Section 8-1 Relationship of Cold Working to the Stress Strain Curve 8-1 8-2 8-3 8-4 8-5 8-6 Using a stress strain diagram, explain what the term "strain hardening" means. What is meant by the term "springback"? What is the significance of this term from a manufacturing viewpoint? What does the term "Bauschinger effect" mean? What manufacturing techniques make use of the cold-working process? What is the difference between extrusion and drawing? Consider the tensile stress strain curves in Figure 8-20 labeled 1 and 2 and answer the following questions. These curves are typical of metals. Consider each part as a separate question that has no relationship to previous parts of the question. 2 True stress (MPa) 8-7 600 500 400 300 200 (c) Assume that the two stress strain curves represent successive tests of the same sample. The sample was loaded, then unloaded before necking began, and then the sample was reloaded. Which sample represents the first test: 1 or 2? How do you know? Figure…arrow_forwardHow can the internal bending and torsion at any cross-section best be determined?arrow_forwardWhat are the important points on the stress-strain diagram?arrow_forward
- Discuss the qualitative changes of burst and collapse resistances when the casing string is become under tension or compression load.arrow_forwardWhat are the cyclic stressess. Explain using S-N curve Hand written only pleasearrow_forwardWhy does the hardness decrease at 600 ° C after rising when the tempering processarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
An Introduction to Stress and Strain; Author: The Efficient Engineer;https://www.youtube.com/watch?v=aQf6Q8t1FQE;License: Standard YouTube License, CC-BY