Degarmo's Materials And Processes In Manufacturing
Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
bartleby

Videos

Textbook Question
Book Icon
Chapter 29, Problem 1RQ

Over the latter half of the 20th century, what drove the manufacture of products with ever-decreasing dimensions?

Expert Solution & Answer
Check Mark
To determine

The effect on manufacture of products with ever-decreasing dimensions.

Explanation of Solution

Over the latter half of the 20th century, more emphasis was made to decrease the dimensions of the products. The drive towards miniaturization of the integrated circuit (IC) invented after solid state transistor to increase the performance of electronic device and decrease the cost.

Now a days, the feature sizes of IC chips ranging approximately four or more order of magnitude from 10nm scale gate length to 100μm scale solder bumps. Smaller gate sizes increase the speed; decrease the cost and permits higher component densities. The requirements of solder bumpsfor the interconnection within the electronic devices.

Nanotechnology involves the length scale of matter between 1 to 100nm and micro technology involves the length scale of matter between 1μm to 1mm . Nanotechnology generally follows bottom-up approach of integration of nanocrystals whereas micro technology follows top-down approach of integration.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
36 2) Use the method of MEMBERS to determine the true magnitude and direction of the forces in members1 and 2 of the frame shown below in Fig 3.2. 300lbs/ft member-1 member-2 30° Fig 3.2. https://brightspace.cuny.edu/d21/le/content/433117/viewContent/29873977/View
Can you solve this for me?
5670 mm The apartment in the ground floor of three floors building in Fig. in Baghdad city. The details of walls, roof, windows and door are shown. The window is a double glazing and air space thickness is 1.3cm Poorly Fitted-with Storm Sash with wood strip and storm window of 0.6 cm glass thickness. The thickness of door is 2.5 cm. The door is Poor Installation. There are two peoples in each room. The height of room is 280 cm. assume the indoor design conditions are 25°C DBT and 50 RH, and moisture content of 8 gw/kga. The moisture content of outdoor is 10.5 gw/kga. Calculate heat gain for living room : الشقة في الطابق الأرضي من مبنى ثلاثة طوابق في مدينة بغداد يظهر في مخطط الشقة تفاصيل الجدران والسقف والنوافذ والباب. النافذة عبارة عن زجاج مزدوج وسمك الفراغ الهوائي 1.3 سم ضعيف الاحكام مع ساتر حماية مع إطار خشبي والنافذة بسماكة زجاج 0.6 سم سماكة الباب 2.5 سم. الباب هو تركيب ضعيف هناك شخصان في كل غرفة. ارتفاع الغرفة 280 سم. افترض أن ظروف التصميم الداخلي هي DBT25 و R50 ، ومحتوى الرطوبة 8…

Chapter 29 Solutions

Degarmo's Materials And Processes In Manufacturing

Ch. 29 - Prob. 11RQCh. 29 - Name two conventional manufacturing processes that...Ch. 29 - Prob. 13RQCh. 29 - Why does breadth of scale of a product have an...Ch. 29 - What is the most complicated, expensive, and...Ch. 29 - Name three purposes that a resist mask can play.Ch. 29 - Name four key lithography methods.Ch. 29 - Name two through-mask lithography techniques.Ch. 29 - Name two direct-write lithography techniques.Ch. 29 - List the sequence of steps involved in...Ch. 29 - Of the two major classifications of photoresists,...Ch. 29 - List four requirements of a photoresist.Ch. 29 - What limits the resolution of a photoresist?Ch. 29 - What is meant by resist sensitivity?Ch. 29 - What is one requirement that contributes to the...Ch. 29 - List the three types of exposure methods used in...Ch. 29 - Why is projection printing equipment called a...Ch. 29 - What are typical materials etched during...Ch. 29 - What is etch bias?Ch. 29 - Prob. 30RQCh. 29 - What are some possible defects that can result...Ch. 29 - What are some possible defects that can result...Ch. 29 - List and describe two properties of etchants.Ch. 29 - What is etch anisotropy dependent upon?Ch. 29 - What is the difference between wet and dry?...Ch. 29 - What is dry etching?Ch. 29 - What are the three main categories of dry etching...Ch. 29 - What is the difference between plasma etching and...Ch. 29 - What is deep reactive ion etching?Ch. 29 - What is a benefit of using UV lasers to machine...Ch. 29 - Which type of non-lithographic micromachining...Ch. 29 - What are thin films?Ch. 29 - A) What is the difference between solution...Ch. 29 - What are the two broad categories of vapor...Ch. 29 - List two different types of physical vapor...Ch. 29 - List two advantages of sputtering over...Ch. 29 - What is meant by step coverage with regards to...Ch. 29 - Why is step coverage important?Ch. 29 - Prob. 49RQCh. 29 - What does gettering mean in relation to wafer...Ch. 29 - How are undesirable gas-phase reactions controlled...Ch. 29 - What is the key difference in the reactor designs...Ch. 29 - What are the two types of LPCVD reactor designs?...Ch. 29 - In metallization, what is the difference between a...Ch. 29 - What is the advantage of using plasma-enhanced on...Ch. 29 - A) What is epitaxy? B) is it important for...Ch. 29 - Name four techniques for solution deposition onto...Ch. 29 - Name four roll-to-roll processing techniques for...Ch. 29 - What is a semiconductor?Ch. 29 - Name three common semiconductor materials.Ch. 29 - Give three reasons why silicon is the most popular...Ch. 29 - Prob. 62RQCh. 29 - What is a silicon boule?Ch. 29 - Prob. 64RQCh. 29 - What are some geometric concerns involved with...Ch. 29 - What is meant by the term doping?Ch. 29 - What is the difference between n�type and...Ch. 29 - Name three methods for doping a silicon wafer.Ch. 29 - Prob. 69RQCh. 29 - Prob. 70RQCh. 29 - Prob. 71RQCh. 29 - Why are rapid thermal processing technologies...Ch. 29 - What are two ways in which silicon dioxide is...Ch. 29 - Give two reasons why wet oxidation is better...Ch. 29 - What is a p�n junction? \What can it be used...Ch. 29 - Prob. 76RQCh. 29 - Assuming an n�doped substrate is clean, list the...Ch. 29 - What is planarization and why is it needed?Ch. 29 - What is meant by the term ULSI?Ch. 29 - In general, what technological breakthroughs were...Ch. 29 - What drives the increase in component density and...Ch. 29 - Why are clean rooms so important to...Ch. 29 - What is the advantage of electron microscopy over...Ch. 29 - What is the collective advantage of...Ch. 29 - Why do samples analyzed in an electron microscopes...Ch. 29 - What are two differences between a scanning...Ch. 29 - What is important about a dual�beam focused ion...Ch. 29 - Why is white light normally preferred for...Ch. 29 - What is one advantage of an atomic force...Ch. 29 - What is the breadth of scale of an automotive...Ch. 29 - What is the breadth of scale of a computer...Ch. 29 - Which has a larger breadth of scale, the...Ch. 29 - Prob. 4PCh. 29 - A piece of silicon has an integrated resistor...Ch. 29 - Based on what you learned in problem #5, which...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Microelectronics Fabrication Center; Author: AnritsuCompany;https://www.youtube.com/watch?v=oDC6WWj3gmk;License: Standard Youtube License