Degarmo's Materials And Processes In Manufacturing

13th Edition

ISBN: 9781119492825

Author: Black, J. Temple, Kohser, Ronald A., Author.

Publisher: Wiley,

See similar textbooks

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many …

Videos

Textbook Question

Chapter 21, Problem 12RQ

How do the magnitude of the strain and strain rate values of metal cutting compare to those of tensile testing?

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 21, Problem 11RQ

Chapter 21, Problem 13RQ

Students have asked these similar questions

Can you answer this question?

A gear has a gear wheel with 16 teeth. The gear should be dimensioned for the highest and lowest gear ratio. Looking for output power, torque, speed?nin= 2000 rpmmin = 30Nmn=0,9a max= 450 mmModule 4Gear limitsz1 z213 13-1614 14-2615 15-4516 16-10117 17-131418 18-…..I have calculate but I can’t get the right answers…..√16 =459x60/56x57=1.1 lowest59x60/13x13=20,94 highestnut=2000/1.1= 1818rpmnut=2000/20.94=95.5 rpmMut=1.1x30=33 NmMut=20.94x30=628,2 Nm(Right answer)LowestZ=13, M=24,4Nm, n=2462 rpmHighestZ=92, M=172,5Nm, n=347,8 rpmP=5655W on both

Please see attached pic.

Chapter 21 Solutions

Degarmo's Materials And Processes In Manufacturing

Ch. 21 - Why has the metal-cutting process resisted...Ch. 21 - What variables must be considered in understanding...Ch. 21 - Which of the seven basic chip formation processes...Ch. 21 - How is feed related to speed in the machining...Ch. 21 - Before you select speed and feed for a machining...Ch. 21 - Milling has two feeds. What are they, and which...Ch. 21 - What is the fundamental mechanism of chip...Ch. 21 - What is the difference between oblique machining...Ch. 21 - What are the implications of Figure 21.13, given...Ch. 21 - Note that the units for the approximate equation...

Ch. 21 - For orthogonal machining, the cutting edge radius...Ch. 21 - How do the magnitude of the strain and strain rate...Ch. 21 - Why is titanium such a difficult metal to machine?...Ch. 21 - Explain why you get segmented or discontinuous...Ch. 21 - Why is metal cutting shear stress such an...Ch. 21 - Which of the three cutting forces in oblique...Ch. 21 - How is the energy in a machining process typically...Ch. 21 - Where does the energy consumed in metal cutting...Ch. 21 - What are two ways of estimating the primary...Ch. 21 - What are the three different ways to perform...Ch. 21 - Why does the cutting force Fc increase with...Ch. 21 - Why doesnt the cutting force Fc increase with...Ch. 21 - Prob. 23RQ Ch. 21 - How does the selection of the machining parameters...Ch. 21 - Suppose you had a machining operation (boring)...Ch. 21 - Make a sketch like that shown in Figure 21.1 with...Ch. 21 - Show how you would do near orthogonal machining in...Ch. 21 - Can you do orthogonal machining on a shaper or...Ch. 21 - What process and material combination would yield...Ch. 21 - What is meant by the statement that machining...Ch. 21 - Prob. 31RQ Ch. 21 - Figure 21.4 provides suggested cutting speeds and...Ch. 21 - For problem 1, suppose you selected a speed of 145...Ch. 21 - If the cutting forces is 1000 lb calculate the...Ch. 21 - Explain how you would estimate the cutting force...Ch. 21 - For a turning operation, you have selected a...Ch. 21 - For a slab milling operation using a...Ch. 21 - The power required to machine metal is related to...Ch. 21 - In order to drill a hole in the material described...Ch. 21 - Suppose you have the data in Table 21.A obtained...Ch. 21 - Calculate the horsepower that a process is going...Ch. 21 - Explain how you would estimate the cutting force...Ch. 21 - Derive equations for F and N using the circular...Ch. 21 - Prob. 14P Ch. 21 - Prob. 15P Ch. 21 - A manufacturing engineer needs an estimate of the...Ch. 21 - Using Figure 21.4 for input data, determine the...Ch. 21 - Estimate the horsepower needed to remove metal at...Ch. 21 - For a turning process, the horsepower required was...

Additional Engineering Textbook Solutions

Find more solutions based on key concepts

When two operators share an operand, the operator with the highest _____ executes first.

Starting Out With Visual Basic (8th Edition)

Write a program that demonstrates type casting of double values by performing the following tasks: Use scanner ...

Java: An Introduction to Problem Solving and Programming (8th Edition)

Assume a telephone signal travels through a cable at two-thirds the speed of light. How long does it take the s...

Electric Circuits. (11th Edition)

ICA 8-54 When we drive our car at 100 feet per second [ft/s], we measure an aerodynamic force (called drag) of ...

Thinking Like an Engineer: An Active Learning Approach (4th Edition)

Given that y=ax3+7, which of the following are correct Java statements for this equations? int y = (a x) x x...

Java How to Program, Early Objects (11th Edition) (Deitel: How to Program)

Porter’s competitive forces model: The model is used to provide a general view about the firms, the competitors...

Management Information Systems: Managing The Digital Firm (16th Edition)

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.