Copyright 2013 Pearson Education, publishing as Prentice Hall 2. Determine the force that the jaws J of the metal cutters exert on the smooth cable C if 100-N forces are applied to the handles. The jaws are pinned at E and A, and D and B. There is also a pin at F. E 400 mm 15° D B 30 mm² 80 mm/ 20 mm 15° $15° 20 mm 400 mm 15° 100 N 100 N 15°

Copyright 2013 Pearson Education, publishing as Prentice Hall 2. Determine the force that the jaws J of the metal cutters exert on the smooth cable C if 100-N forces are applied to the handles. The jaws are pinned at E and A, and D and B. There is also a pin at F. E 400 mm 15° D B 30 mm² 80 mm/ 20 mm 15° $15° 20 mm 400 mm 15° 100 N 100 N 15°

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.75P: The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft...

See similar textbooks

Similar questions

3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections are identical except for the diameter, prove that the following equations are true when temperature rises to T₂. a. F= b. OAB C. OBC A x(T₂-T₁)лd²E 20 x(T₂-T₁)E 5 9x(T₂-T₁)E 5 -1/2- d B 1/12- d C
only HANDWRITTEN answer needed ( NOT TYPED)
Subject: meca
Subject: mechanical
1.2.2 If a force of F = 350 N is applied to the handle of the toggle clamp, determine the resulting clamping force at A.
plase no hand writing solution
The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
5a. If lengths a=1.2m, b=3.7m, c=1.6m, d=4, e=1.4m, and f=4.3m, determine the angle (in degree) between the forces F_A and F_B. Answer must include 1 place after the decimal point. 5b. If lengths a=1.1m, b=4.8m, c=1.1m, d=3.2, e=1.3m, and f=3.2, determine the moment (in N*m) caused by force F_A about axis OD. Answer must include 1 place after the decimal point. Negative sign must be included if the rotational tendenct about the OD axis (from O to D) is clockwise. 5c. Find out all support reaction components at the fixed support O after being given all forces and lengths. ( use the 2nd image named practice problem 5-2 for this question)
! Required information Bar AC supports two loads, X = 355 N and Y= 355 N as shown. Rollers at A and Crest against frictionless surfaces and a cable BD is attached at B. 100 mm 100 mm A X 150 mm B - 300 mm - 500 mm The tension in cable BD = D Determine the tension in cable BD. (Round the final answer to one decimal place.) |N 250 mm
2-26 if you could
1: Determine the magnitude of F, and length y if F;=1500 N and x =1.75 m. You may assume that the tension in a rope on one side of a pulley is equal to the tension in the rope on the other side of the pulley. In making this assumption, you are neglecting the effects of friction. 2m
The two rods (A-B and B-C) shown in the left panel are connected by pins at A, B, and C. The cross sections of A-B and B-C are 10mm×13mm and 10mm×10mm, respectively. The bilinear stress-strain relation shown in the right panel is for the material used to make the two rods, where Ei is the slope of the stress-strain curve for stresses between 0 and 80 MPa and E2 is the slope for stresses larger than 80 MPa. Note that Hooke's law is only valid for stresses up to 80 MPa. A 1 1 B 0.900 m 3 P = 30 kN 2.44 m C σ MPa 80 E₂ = 40 GPa E₁ = 80 GPa E a) Given the conditions above, find the axial elongation for each rod when subjected to P=30KN. b) Find the final position of Point B due to the applied load P at that location. Hint: Assume point B moves by unknown amounts Ax and Ay from its initial position, and then use right triangles to write the known final lengths of the cables in terms of Ax and Ay. The equations can be simplified by assuming terms Ax² and Ay² are so small they can be…