1. A 40 lb. force is applied at point E. There are pins atA, B, C, D, and F and a roller at A.a. Draw a FBD of member EFC showing all the known andunknown forces acting on it.b. Draw a FBD of member ABF showing all the known andunknown forces acting on it.c. Draw a FBD of member BCD showing all the known andunknown forces acting on it.d. Draw a FBD of the entire assembly ADE showing all theknown and unknown forces acting on it.e. Determine the reactions at A and D.f. Determine the magnitude of the pin reaction at C.40 lbs.BA6 in.4 in.DF-5 in.4 in 4.

Step 1: Step 2: Step 3: Step 4:

Answered: 1. A 40 lb. force is applied at point…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.4P: Find the internal force systems acting on sections 1 and 2.

See similar textbooks

Similar questions

Q3) A lug wrench is used to tighten a square-head bolt. If 50-lb forces are applied to the wrench as shown, determine the magnitude F of the equal forces exerted on the four contact points on the 1-in. bolt head so that their external effect on the bolt is equivalent to that of the two 50-lb forces. Assume that the forces are perpendicular to the flats of the bolt head. 50 lb A View C Detail (clearances exaggerated) 14" 50 lb 14" B. Q4) A commercial airliner with four jet engines, each producing 90 kN of forward thrust, is in a steady, level cruise when engine number 3 suddenly fails. Determine and locate the resultant of the three remaining engine thrust vectors. Treat this as a two-dimensional problem. 4 90 kN 9 m 12 m 12 m 90 kN 9 m 90 kN 1 Good luck
36 2) Use the method of MEMBERS to determine the true magnitude and direction of the forces in members1 and 2 of the frame shown below in Fig 3.2. 300lbs/ft member-1 member-2 30° Fig 3.2. https://brightspace.cuny.edu/d21/le/content/433117/viewContent/29873977/View
2. Find the forces acting at pins C and D of the given frame. loworod slowly onto 2.2 m -3 m 2m DI 3 m3 m- B 4 m 240 N
240 lb B 2. Find the horizontal and vertical forces at Point C as it acts on Member BD. D 45° 450 E -8'-
a. A plate is supported by 4 concurrent forces. If the resultant force on the plate is zero what will be the condition of the plate? b. A 600-lb force F1 and an 800-lb force F2 are applied to the plate through a smooth pin. i. Draw the free body diagram and ii. determine the magnitudes of forces FA and FB if the resultant R of the four forces is zero. Plz complete solution otherwise skip...
3
The cantilever truss shown is hinged at D and E. Find the forces in each members. 5 kN 60° 60° 30° E 3m 6m 5 kN 5 kN
The following forces are acting on the bracket below (a free-body diagram of the bracket is shown), that is hinged at point 1 (bottom left point). The bracket is in equilibrium (not accelerating). The force at point 2 must act horizontally, but can act to the right or left. I drew the force acting at point 2 (the middle point) pushing the bracket to the right. For the given forces, did I draw the force acting on the bracket in the correct direction? F2 F1x 10 Ibf Yes No Can't be determined based on the given information
4. Find the x-component and the y-component of the forces in 1200 Ib Frg. 2a
In the assembly shown, member AB is rigidly attached to the wall while an L bar is pinned to AB at E. Two forces P and Q are acting on the assembly as shown. Force P lies on the x-axis while force Q is applied at point D along a plane parallel to the yz plane. 1. Which of the following quantities is/are zero? (Choices: A. Moment of P about the x-axis ; B. Moment of P about the y-axis ; C. Moment of P about the z-axis) 2. Which of the following best approximates the moment of force Q about point A? 3. Which of the following best approximates the equivalent force-couple set at point A of the applied forces P and Q? Note: F is the resultant force and Cis the resultant couple4. Considering the force diagram of member DE, which gives the complete set of reactions for the support at E? (Note difference of Force and couple reactions)
Replace the loading shown by a single equivalent force. Specify the magnitude and direction of this force and its location where it intersects (a) AB measured from point A, (b) BC measured from point C. (Hint: Can you find a point where you can find a force-couple that you can use for both parts of this problem? You may find the examples posted in Canvas helpful.) 10 lb 3 in. 300 lb • in. 5 in. 200 lb • in. В 5) 12 4 in. 4 in. 4 in. 39 lb 25 lb
Find the internal force systems acting on sections 1 and 2.

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L