The following forces are acting on the bracket below (a free-body diagram of the bracket is shown), that is hinged at point 1 (bottom left point). The bracket is in equilibrium (not accelerating). The force at point 2 must act horizontally, but can act to the right or left. I drew the force acting at point 2 (the middle point) pushing the bracket to the right. For the given forces, did I draw the force acting on the bracket in the correct direction? F2 F1x 10 Ibf Yes No O Can't be determined based on the given information

The following forces are acting on the bracket below (a free-body diagram of the bracket is shown), that is hinged at point 1 (bottom left point). The bracket is in equilibrium (not accelerating). The force at point 2 must act horizontally, but can act to the right or left. I drew the force acting at point 2 (the middle point) pushing the bracket to the right. For the given forces, did I draw the force acting on the bracket in the correct direction? F2 F1x 10 Ibf Yes No O Can't be determined based on the given information

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter2: Basic Operations With Force Systems

Section: Chapter Questions

Problem 2.80P: The figure shows one-half of a universal coupling known as the Hooke's joint. The coupling is acted...

See similar textbooks

Similar questions

Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
Help!
A truss is facing a two-force member and both of them are in the opposite directions, and the truss is in equilibrium. And both of them are coming to each other. The forces are called Select one: O a. Tensile Forces O b. Compressive forces O c Parallel and collinear forces with same direction of heading O d. The rotational forces Next page est-3 Jump to...
The weight of the limb is W=15 lbs.The contact of foot with the ground can be modeled as a pin/hinge here. Determine the reaction force of the ground and the reaction at the knee joint and its direction/angle θ. Note: use the thee force member condition to find the angle of FK.Q4.As it’s been shown in the below figure,a person is using an exercise machine. Points A and B correspond to the shoulder and elbow joints, respectively. Relative to the person, the upper arm (AB) is extended toward the left (x-direction) and the lower arm (BC) is extended forward (z-direction). At this instant, the person is holding a handle that is connected by a cable to a suspending weight. The weight applies an upward (in the y-direction) force with magnitude F on the arm at point C. The lengths of the upper arm and lower arm are AB̅̅̅̅= 20cm and BC̅̅̅̅= 25cm, respectively, and the magnitude of the applied force is F = 400 N.Determine the components of reaction developed at the shoulder joint A When the…
perpendicular to the page through the point o. (Let counterclockwise torque be positive and let forces to the right and up be positive. Use the following as necessary: the forces R, Write the necessary equations of equilibrium of the object shown in the figure below. Take the origin of the torque equation about an axis RFF, and F the length l of the object; and the angle e that the object makes with the horizontal.) EF, = = 0 Fy =0 Στ. =0 Need Help? Read It
This is homework question #3 Pls help
Q3: The diagram shows the open bonnet of a car. The bonnet is yarie tore V held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The is 0.90 m long, has a weight of 25 N and its center of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. 2) By taking moments about 0, show that the vertical force V applied at the end of the bonnet is 9.7 N. Neg 0 3) Caleulate the magnitude of the force acting at the hinge O.
1. The man is holding up the 35-kg ladder ABC by pushing perpendicular to the ladder. If the maximum force that the man can exert is 400 N, determine the smallest angle e at which he can support the ladder. (Figure P4-20)
None
3
In the 4-cable setup, find the tension in each cable to maintain the equilibrium of the system.
Statics, A hand-powered can crusher is shown in the figure. If a force of F is applied at C, find the magnitude of the vertical component of the force exerted on the can at D and the horizontal and vertical reactions at A.