Heat and Mass Transfer: Fundamentals and Applications
5th Edition
ISBN: 9780073398181
Author: Yunus A. Cengel Dr., Afshin J. Ghajar
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 2, Problem 120P
A spherical tank is filled with ice slurry, where its inner surface is at 0°C. The tank has an inner diameter of 9 m, and its wall thickness is 20 mm. The tank wall is made of a material with a thermal conductivity given as
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A spherical tank of 3 m diameter contains a gas at -60°C. Insulation with a thermal conductivity of
k=0.06 W/m.k and thickness 250 mm is applied to the tank, the outer surface of the insulation is
subjected to the fluid Too-20 °C, hoo-6 W/m².k. Determine the rate of heat transfer and find the
temperature at radial position r=1.687 m.
The wall of a house is 7m wide and 6m high and is made from 0.3 m thick brick with a coefficient of thermal conductivity k = 0.6 W/m-K. The surface temperature inside the house is 6°C and that on the outside is 18°C. Find the amount of heat flow on the wall.
Q: A large plane wall of thickness (L= 0.3 m), thermal conductivity (k = 40 W/m-°C),
and surface area 0.4 m2. The left side of the wall is maintained at a constant temperature
of 70°C while the right side loses heat to the surrounding air with heat flux q' expressed
by:
1200k
q = k+20L
A- Find a relation to determine the variation of temperature in the wall.
B- Determine the rate of heat transfer through the wall.
C- Determine the temperature at the right side of the wall.
wall
T1= 70 °C
L= 0.3m
Chapter 2 Solutions
Heat and Mass Transfer: Fundamentals and Applications
Ch. 2 - How does transient heat transfer from steady heat...Ch. 2 - Is heat transfer a scalar or a vector quantity?...Ch. 2 - Does a hear flux vector at a point P on an...Ch. 2 - From a heat transfer point of view, what is the...Ch. 2 - What is heat generation in a solid? Give examples.Ch. 2 - Heat generation is also referred to as energy...Ch. 2 - In order to size the compressor of a new...Ch. 2 - In order to determine the size of the heating...Ch. 2 - Consider a round potato being baked in an oven....Ch. 2 - Consider an egg being cooked in boiling water in a...
Ch. 2 - Prob. 11CPCh. 2 - Consider the cooking process of a roast beef in an...Ch. 2 - Consider heat loss from a 200-L cylindrical hot...Ch. 2 - Consider a cold canned drink left on a dinner...Ch. 2 - Heat flux meters use a very sensitive device know...Ch. 2 - Consider a large 3-cm-thick stainless steel plate...Ch. 2 - In a nuclear reactor, heat is generated uniformly...Ch. 2 - Prob. 18PCh. 2 - Prob. 19EPCh. 2 - Writer down the one-dimensional transient heat...Ch. 2 - Writer down the one-dimensional transient heat...Ch. 2 - Starting with an energy balance on rectangular...Ch. 2 - Prob. 23PCh. 2 - Prob. 24PCh. 2 - Consider a medium in which the heat conduction...Ch. 2 - Consider a medium in which the heat conduction...Ch. 2 - Consider a medium in which the heat conduction...Ch. 2 - Consider a medium in which the heat conduction...Ch. 2 - Consider a medium in which the heat conduction...Ch. 2 - Consider a medium in which the heat conduction...Ch. 2 - Consider a medium in which the heat conduction...Ch. 2 - Starting with an energy balance on a volume...Ch. 2 - Prob. 33PCh. 2 - Prob. 34PCh. 2 - What is a boundary condition? How many boundary...Ch. 2 - What is an initial condition? How many initial...Ch. 2 - What is a thermal symmetry boundary condition? How...Ch. 2 - How is the boundary condition on an insulated...Ch. 2 - It is claimed that the temperature profile in a...Ch. 2 - Why do we try to avoid the radiation boundary...Ch. 2 - Consider an aluminum pan used to cook stew on top...Ch. 2 - Prob. 42PCh. 2 - Prob. 43PCh. 2 - Heat is generated in a long wire of radius ro at a...Ch. 2 - Consider a long pipe of inner radius r1, Outer...Ch. 2 - A 2-kW resistance heater wire whose thermal...Ch. 2 - Prob. 47PCh. 2 - Prob. 48PCh. 2 - Consider a spherical shell of inner radius r1,...Ch. 2 - A container consists of two spherical layers, A...Ch. 2 - A spherical metal ball of radius ro is heated in...Ch. 2 - Prob. 52PCh. 2 - It is stated that the temperature in a plane wall...Ch. 2 - Consider one-dimensional heat conduction through a...Ch. 2 - Consider a solid cylindrical rod whose side...Ch. 2 - Consider a solid cylindrical rod whose ends are...Ch. 2 - Prob. 57PCh. 2 - Prob. 58PCh. 2 - Prob. 59PCh. 2 - Consider a 20-cm-thick concrete plane wall...Ch. 2 - Prob. 61PCh. 2 - Prob. 62PCh. 2 - Prob. 63PCh. 2 - Prob. 64PCh. 2 - Prob. 65EPCh. 2 - Prob. 66PCh. 2 - Consider a chilled-water pipe of length L, inner...Ch. 2 - Prob. 68EPCh. 2 - Prob. 69PCh. 2 - Prob. 70PCh. 2 - Prob. 71PCh. 2 - Prob. 72PCh. 2 - Prob. 73PCh. 2 - Prob. 74PCh. 2 - Prob. 75PCh. 2 - Prob. 76PCh. 2 - Prob. 77PCh. 2 - Prob. 78CPCh. 2 - Does heat generation in a solid violate the first...Ch. 2 - Prob. 80CPCh. 2 - Prob. 81CPCh. 2 - Prob. 82CPCh. 2 - Prob. 83PCh. 2 - Prob. 84PCh. 2 - Consider a large 3-cm thick stainless steel plate...Ch. 2 - Prob. 86PCh. 2 - Prob. 87EPCh. 2 - Prob. 88PCh. 2 - Prob. 89PCh. 2 - Prob. 90PCh. 2 - Heat is generated uniformly at a rate of 3 kW per...Ch. 2 - Prob. 92PCh. 2 - Prob. 93PCh. 2 - Prob. 94PCh. 2 - Prob. 95PCh. 2 - Prob. 96PCh. 2 - Prob. 97PCh. 2 - Prob. 98PCh. 2 - Prob. 99PCh. 2 - Prob. 100PCh. 2 - Prob. 101PCh. 2 - Prob. 102PCh. 2 - Prob. 103PCh. 2 - Prob. 104CPCh. 2 - When the thermal conductivity of a medium varies...Ch. 2 - The temperature of a plane wall during steady...Ch. 2 - Consider steady one-dimensional heat conduction in...Ch. 2 - Prob. 108CPCh. 2 - Prob. 109PCh. 2 - Prob. 110PCh. 2 - Prob. 111PCh. 2 - Consider a plane wall of thickness L whose thermal...Ch. 2 - Prob. 113PCh. 2 - Prob. 114PCh. 2 - A pipe is used for transporting boiling water in...Ch. 2 - Prob. 116PCh. 2 - Prob. 117PCh. 2 - Consider a spherical shell of inner radius r1 and...Ch. 2 - Prob. 119PCh. 2 - A spherical tank is filled with ice slurry, where...Ch. 2 - Prob. 121CPCh. 2 - Prob. 122CPCh. 2 - Can a differential equation involve more than one...Ch. 2 - Prob. 124CPCh. 2 - Prob. 125CPCh. 2 - Prob. 126CPCh. 2 - Prob. 127CPCh. 2 - How is integation related to derivation?Ch. 2 - Prob. 129CPCh. 2 - Prob. 130CPCh. 2 - How is the order of a differential equation...Ch. 2 - How do you distinguish a linear differential...Ch. 2 - How do you recognize a linear homogeneous...Ch. 2 - How do differential equations with constant...Ch. 2 - What kinds of differential equations can be solved...Ch. 2 - Consider a third-order linear and homogeneous...Ch. 2 - A large plane wall, with a thickness L and a...Ch. 2 - Prob. 138PCh. 2 - Prob. 139EPCh. 2 - A spherical vessel has an inner radius r1 and an...Ch. 2 - Consider a short cylinder of radius r0 and height...Ch. 2 - Prob. 142PCh. 2 - Prob. 143PCh. 2 - Consider a 20-cm-thick large concrete plane wall...Ch. 2 - Prob. 145PCh. 2 - Prob. 146PCh. 2 - Prob. 147EPCh. 2 - Prob. 148PCh. 2 - In a manufacturing plant, a quench hardening...Ch. 2 - Consider a water pipe of length L=17m, inner...Ch. 2 - Prob. 151PCh. 2 - Consider a spherical reactor of 5-cm diameter...Ch. 2 - Consider a cylindrical sheel of length L, inner...Ch. 2 - A pipe is used for transporting boiling water in...Ch. 2 - A metal spherical tank is filled with chemicals...Ch. 2 - The heat conduction equation in a medium is given...Ch. 2 - Consider a medium in which the heat conduction...Ch. 2 - Consider a large plane wall of thicness L, thermal...Ch. 2 - A solar heat flux qs is incident on a sidewalk...Ch. 2 - A plane wall of thickness L is subjected to...Ch. 2 - Consider steady one-dimensional heat conduction...Ch. 2 - The conduction eqution boundary condition for an...Ch. 2 - Prob. 163PCh. 2 - Prob. 164PCh. 2 - The temperatures at the inner and outer surfaces...Ch. 2 - The thermal conductivity of a solid depends upon...Ch. 2 - Prob. 167PCh. 2 - Prob. 168PCh. 2 - Prob. 169PCh. 2 - Prob. 170PCh. 2 - Prob. 171PCh. 2 - Write essay on heat generation in nuc1e e1 rods....Ch. 2 - Write an interactive computer program to calculate...Ch. 2 - Prob. 174P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinderarrow_forwardWhat’s the correct answer for this please ?arrow_forwardKindly give me right solutions with clear calculations.arrow_forward
- Its thickness is 1.18 m, its thermal conductivity is 2.75 W/m.°C and its surface area is 15m2Consider a wide plane wall. Inside of the base plateThere is a uniform heat flux produced on its surface with the help of the resistance wire inside.590 W/m2 on the left surface of the wall at x=0net heat fluxand the temperature on this surface was measured as 590 °C. On the wallassuming that there is no heat generation and that the thermal conductivity is constant;a) The differential equation for continuous one-dimensional heat conduction in the wall, andSet the boundary conditions.b) Solve the differential equation to obtain a relation for the temperature change at the wall.c) Calculate the heat loss rate from the wall.arrow_forwardyo lo:ll O %AV L. مرتضی نشط الآن Q5: The piston cylinder device (radius=10 cm) contains a liquid with a pressure 100 kpa and temperature of 20 ° C and has a liquid convection heat coefficient =93 WmK. Connect its fixed side to a cubic piece of aluminum (side length 15 cm) with a thermal conductivity coefficient of aluminum = 239 W mK. At the bottom of the aluminum piece there is a heat source with a temperature of 150 ° C, noting that the heat source is located in a vacuum chamber. Radiation thermal resistance = 3.17 K/W. Calculate the change in piston height during I sec. if you know that there is no change in the internal energy of the piston cylinder device. Note IK Watt 1KJ/s : Aaarrow_forwardThe temperature distribution across a wall 0.3 m thick at a certain instant of time is T(x) = a+ b+cx?, where T is in degrees Celsius and x is in meters, a = 200°C,b = -200°, and c = conductivity of 1 W /m · K. 30°C/m² . The wall has a thermal (a) On a unit surface area basis, determine the rate of heat transfer into and out of the wall and the rate of change of energy stored by the wall. (b) If the cold surface is exposed to a fluid at 100°C, what is the convection coefficient? k=1W/m•k T(x) =200-200x + 30x² 200°C- ĖST 142.7°C q"out | Fluid Too = 100°C,h 9"in |L-0.3marrow_forward
- Consider an apartment in a tower block as a cube of side L = 7.26 m. Since this apartment is designed to be rented by a student, it has no windows. The floor and ceiling are perfectly insulated, but the wall is made of concrete of thickness d = 19.1 cm. The thermal conductivity of the concrete is k = 0.567 Wm¬'K-1. Part 1) The outside temperature is stable at Tout = 35.6°C. What is the heat load (rate of heat transfer) on the air conditioner if the occupant wants to keep the inside temperature stable at Tn = 20.3°C? P = kW Part 2) A layer of insulation of thickness dins = 30.7 mm and thermal conductivity kins = 0.0105 Wm¬1K-l is added to the walls. What is the heat load now? P = kW Part 3) The occupant complains that the apartment is dank and dark, so the landlord is forced to install windows and a door. These are constructed, but then drafts from the gaps around the windows and doors allow the air in the apartment to change every 2 hours. How much additional heat load does changing…arrow_forwardIn a solid sphere of 0.2 m diameter, heat is generated at the rate of 1.2 x 106 W/m3. The center temperature is 300°C. Conductivity is 50 W/m-K. What is the surface temperature?arrow_forwardQ₁: Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k-2.3 W/m °C, and surface area A= 20 m². The left side of the wall at x= 0 is subjected of T1 = 80°C. while the right side losses heated by convection to the surrounding air at T-15 °C with a heat transfer coefficient of h=24 W/m² °C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat transfer through the wall Ans: (c) 6030 Warrow_forward
- Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k=2.3 W/m °C,and surface area A= 20 m2. The left side of the wall at x= 0 is subjected of T1 = 80 C. while the right side losses heated by convection to the surrounding air at Too=15 C with a heat transfer coefficient of h=24 W/m2 .C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat transfer through the wallarrow_forwardA house has a three meter deep basement (foundation) wall that is in a 10 meter by eight meter rectangular shape based on interior dimensions. On average, 2.5 meters of the wall is below grade. Assume the outside air temperature is 38°C and the inside temperature is 20°C; there is an average ground temperature of 27°C. Determine the rate of heat loss through the wall if it is insulated with an R-value of about 30°C.m^2/W.arrow_forward1. A residential building has height of 50 m and floor area (25 m x 30 m) as shown in figure below. It is occupied by 200 people. The external walls of the building has conductance ( C= 2 W/m?.°C ). The building has windows occupy about 25% from the outer area. The glass type of windows is clear with thickness of 6 mm. The overall heat transfer coefficient for the roof of the building is ( UR = 1.2 W/m?.°C ). The ventilation requirements is ( 36 m3/(hr. Person)) . The room design conditions is ( t; = 22 °C and RH= 40 %) and outside design conditions is (to = 0 °C and RH=70%). (neglect the heat loss to the ground and infiltration air) calculate the total heating load for the building. 30 m 25 m 50 marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license