A two-color pyrometer is a device that is used to measure the temperature of a diffuse surface, T s . The device measures the spectral, directional intensity emitted by the surface at two distinct wavelengths separated by Δ λ . Calculate and plot the ratio of the intensities I λ + Δ λ , e ( λ + Δ λ , θ , ϕ , T s ) and I λ , e ( λ , θ , ϕ , T s ) as a funtion of the surface temperature over the range 500 K ≤ T s ≤ 1000 K for λ =5 μ m and Δ λ = 0.1 , 0.5 , a n d 1 μ m . Comment on the sensitivity to temperature and on whether the ratio depends on the emissivity of the surface. Discuss the tradeoffs associated with specification of the various values of Δ λ . Hint: The change in the emissivity over small wavelength intervals is modest for most solids, as evident in Figure 12.17.
A two-color pyrometer is a device that is used to measure the temperature of a diffuse surface, T s . The device measures the spectral, directional intensity emitted by the surface at two distinct wavelengths separated by Δ λ . Calculate and plot the ratio of the intensities I λ + Δ λ , e ( λ + Δ λ , θ , ϕ , T s ) and I λ , e ( λ , θ , ϕ , T s ) as a funtion of the surface temperature over the range 500 K ≤ T s ≤ 1000 K for λ =5 μ m and Δ λ = 0.1 , 0.5 , a n d 1 μ m . Comment on the sensitivity to temperature and on whether the ratio depends on the emissivity of the surface. Discuss the tradeoffs associated with specification of the various values of Δ λ . Hint: The change in the emissivity over small wavelength intervals is modest for most solids, as evident in Figure 12.17.
Solution Summary: The author explains the R value (ratio of intensities) emitted from surface at nominal wavelength oflambda.
A two-color pyrometer is a device that is used to measure the temperature of a diffuse surface,
T
s
. The device measures the spectral, directional intensity emitted by the surface at two distinct wavelengths separated by
Δ
λ
. Calculate and plot the ratio of the intensities
I
λ
+
Δ
λ
,
e
(
λ
+
Δ
λ
,
θ
,
ϕ
,
T
s
)
and
I
λ
,
e
(
λ
,
θ
,
ϕ
,
T
s
)
as a funtion of the surface temperature over the range
500
K
≤
T
s
≤
1000
K
for
λ
=5
μ
m
and
Δ
λ
=
0.1
,
0.5
,
a
n
d
1
μ
m
. Comment on the sensitivity to temperature and on whether the ratio depends on the emissivity of the surface. Discuss the tradeoffs associated with specification of the various values of
Δ
λ
. Hint: The change in the emissivity over small wavelength intervals is modest for most solids, as evident in Figure 12.17.
A pump delivering 230 lps of water at 30C has a 300-mm diameter suction pipe and a 254-mm diameter discharge pipe as shown in the figure. The suction pipe is 3.5 m long and the discharge pipe is 23 m long, both pipe's materials are cast iron. The water is delivered 16m above the intake water level. Considering head losses in fittings, valves, and major head loss. a) Find the total dynamic head which the pump must supply. b)It the pump mechanical efficiency is 68%, and the motor efficiency is 90%, determine the power rating of the motor in hp.
The tensile 0.2 percent offset yield strength of AISI 1137 cold-drawn steel bars up to 1 inch in diameter from 2 mills and 25 heats is
reported as follows:
Sy 93
95
101
f
97 99
107 109 111
19 25 38 17 12 10 5 4
103
105
4
2
where Sy is the class midpoint in kpsi and fis the number in each class.
Presuming the distribution is normal, determine the yield strength exceeded by 99.0% of the population.
The yield strength exceeded by 99.0% of the population is
kpsi.
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.