Concept explainers
A 15,000-N crane pivots around a friction-free axle at its base and is supported by a cable making a 25° angle with the crane (Fig. E11.18). The crane is 16 m long and is not uniform, its center of gravity being 7.0 m from the axle as measured along the crane. The cable is attached 3.0 m from the upper end of the crane. When the crane is raised to 55° above the horizontal holding an 11,000-N pallet of bricks by a 2.2-m, very light cord, find (a) the tension in the cable and (b) the horizontal and vertical components of the force that the axle exerts on the crane. Start with a free-body diagram of the crane.
Figure E11.18
Learn your wayIncludes step-by-step video
Chapter 11 Solutions
University Physics with Modern Physics (14th Edition)
Additional Science Textbook Solutions
Cosmic Perspective Fundamentals
Life in the Universe (4th Edition)
Conceptual Integrated Science
Applied Physics (11th Edition)
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
Sears And Zemansky's University Physics With Modern Physics
- A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = ℓ. A painter of mass m stands on the ladder a distance d from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P10.73 Problems 73 and 74.arrow_forwardA stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately.arrow_forwardA uniform beam resting on two pivots has a length L = 6.00 m and mass M = 90.0 kg. The pivot under the left end exerts a normal force n1 on the beam, and the second pivot located a distance = 4.00 m from the left end exerts a normal force n2. A woman of mass m = 55.0 kg steps onto the left end of the beam and begins walking to the right as in Figure P10.28. The goal is to find the womans position when the beam begins to tip. (a) What is the appropriate analysis model for the beam before it begins to tip? (b) Sketch a force diagram for the beam, labeling the gravitational and normal forces acting on the beam and placing the woman a distance x to the right of the first pivot, which is the origin. (c) Where is the woman when the normal force n1 is the greatest? (d) What is n1 when the beam is about to tip? (e) Use Equation 10.27 to find the value of n2 when the beam is about to tip. (f) Using the result of part (d) and Equation 10.28, with torques computed around the second pivot, find the womans position x when the beam is about to tip. (g) Check the answer to part (e) by computing torques around the first pivot point. Figure P10.28arrow_forward
- A 10.0-kg monkey climbs a uniform ladder with weight 1.20 102 N and length L = 3.00 m as shown in Figure P12.14. The ladder rests against the wall and makes an angle of = 60.0 with the ground. The upper and lower ends of the ladder rest on frictionless surfaces. The lower end is connected to the wall by a horizontal rope that is frayed and can support a maximum tension of only 80.0 N. (a) Draw a force diagram for the ladder. (b) Find the normal force exerted on the bottom of the ladder. (c) Find the tension in the rope when the monkey is two-thirds of the way up the ladder. (d) Find the maximum distance d that the monkey can climb up the ladder before the rope breaks. (e) If the horizontal surface were rough and the rope were removed, how would your analysis of the problem change? What other information would you need to answer parts (c) and (d)? Figure P12.14arrow_forwardA bridge of length 50.0 m and mass 8.00 104 kg is supported on a smooth pier at each end as shown in Figure P12.25. A truck of mass 3.00 104 kg is located 15.0 m from one end. What are the forces on the bridge at the points of support? Figure P12.25arrow_forwardIn Figure P10.40, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg; and the pulley is a hollow cylinder with a mass of M = 0.350 kg, an inner radius of R1 = 0.020 0 m, and an outer radius of R2 = 0.030 0 m. Assume the mass of the spokes is negligible. The coefficient of kinetic friction between the block and the horizontal surface is k = 0.250. The pulley turns without friction on its axle. The light cord does not stretch and does not slip on the pulley. The block has a velocity of vi = 0.820 m/s toward the pulley when it passes a reference point on the table. (a) Use energy methods to predict its speed after it has moved to a second point, 0.700 m away. (b) Find the angular speed of the pulley at the same moment. Figure P10.40arrow_forward
- A ladder whose length L is 12m and whose mass m is 45kg rests against a wall. Its upper end is a distance h of 9.3m above the ground. The center of gravity of the ladder is one-third of the way up the ladder. A firefighter whose mass M is 72kg climbs halfway up to the ladder. Assume that the wall, but not the ground is frictionless. What forces are exerted on the ladder by the wall and by the ground?arrow_forwardWe can model a pine tree in the forest as having a compact canopy at the top of a relatively bare trunk. Wind blowing on the top of the tree exerts a horizontal force, and thus a torque that can topple the tree if there is no opposing torque. Suppose a tree’s canopy presents an area of 9.0 m2 to the wind centered at a height of 7.0 m above the ground. (These are reasonable values for forest trees.) If the wind blows at 6.5 m/s: a. What is the magnitude of the drag force of the wind on the canopy? Assume a drag coefficient of 0.50.b. What torque does this force exert on the tree, measured about the point where the trunk meets the ground?arrow_forwardThe femur of a human leg (mass 10 kg, length 0.9 m) is in traction, as shown in the figure. The center of gravity of the leg is one-third of the distance from the pelvis to the bottom of the foot. Two objects, with masses mj and m2, m, are hung at the ends of the leg using pulleys to provide upward support. A third object of 8 kg is hung to provide tension along the leg. The body provides tension as well. body Write a mathematical relationship relating mi to m2 in terms of m2 and numerical coefficients. 8 kg mj = m- m2 Incorrect Is the expression for m1 valid for more than one pair of values of mj and m2? yes no Incorrect Suppose the tension force due to mj is now applied at the leg's center of mass. Write a new expression relating m, to m2 in terms of m2, numerical coefficients, and given values. If you use a given value in your equation, enter it as a number without units.arrow_forward
- A uniform plank of length 5.0 m and weight 225 N rests horizontally on two supports, with 1.1m of the plank hanging over the right support. To what distance x can a person who weighs 377 N walk on the overhanging part of the plank before it just begins to tip?arrow_forwardA74 kg window cleaner uses a 15 kg ladder that is 6.7 m long. He places one end on the ground 3.0 m from a wall, rests the upper end against a cracked window, and climbs the ladder. He is 3.5 m up along the ladder when the window breaks, Neglect friction between the ladder and window and assume that the base of the ladder does not slip. When the window is on the verge of breaking, what are (a) the magnitude of the force on the window from the ladder, (b) the magnitude of the force on the ladder from the ground, and (c) the angle (relative to the horizontal) of that force on the ladder? (a) Number Units (b) Number Units (c) Number Unitsarrow_forwardA 4.0 m long red beam weighs 1500N and is connected to a wall by a frictionless hinge and it is supported by two cables as shown in the image. The tension in the cables are both equal in magnitude to the weight of the beam and they are both connected to the free end of the beam by distance x. What is x if the beam is in equilibrium?arrow_forward
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning