Materials for Civil and Construction Engineers (4th Edition)
4th Edition
ISBN: 9780134320533
Author: Michael S. Mamlouk, John P. Zaniewski
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 1, Problem 1.34QP
A metal rod having a diameter of 10 mm is subjected to a repeated tensile load. The material of the rod has a tensile strength of 290 MPa and a fatigue failure behavior as shown in Figure 1.16. How many load repetitions can be applied to this rod before it fails if the magnitude of the load is (a) 5 kN and (b) 11 kN?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Consider a metal bar 12.5 mm in diameter and 50 mm in length that is tested under uniaxial tension. The test results data are as follows:
Force (kN)
Final length (mm)
Final diameter (mm)
122
56,14
12,19
120
62,05
11,60
114
68,57
11,03
(a) Complete the following table:
Force (kN)
Final length (mm)
Final diameter (mm)
True stress (MPa)
True deformation (mm/mm)
122
56,14
12,19
120
62,05
11,60
114
68,57
11,03
(b) Determine the metal's work hardening coefficient.
(c) The most likely crystal structure for this metal is?
2. A steel bar, whose cross section is 0.55
inch by 4.05 inches, was tested in tension. An
axial load of P = 30,500 lb. produced a
deformation of 0.105 inch over a gauge
length of 2.05 inches and a decrease of
0.0075 inch in the 0.55-inch thickness of the
bar.
*
Determine the lateral strain.
Your answer
Determine the axial strain.
Your answer
Determine the Poisson's rati v.
Your answer
Determine the decrease in the 4.05-in.
cross-sectional dimension (in inches). *
Your answer
Answer asap with solution
Chapter 1 Solutions
Materials for Civil and Construction Engineers (4th Edition)
Ch. 1 - State three examples of a static load application...Ch. 1 - A material has the stressstrain behavior shown in...Ch. 1 - A tensile load of 50.000 lb is applied to a metal...Ch. 1 - A tensile load of 190 kN is applied to a round...Ch. 1 - A cylinder with a 6.0 in. diameter and 12.0 in....Ch. 1 - A metal rod with 0.5 inch diameter is subjected to...Ch. 1 - A rectangular block of aluminum 30 mm 60 mm 90...Ch. 1 - A plastic cube with a 4 in. 4 in. 4 in. is...Ch. 1 - A material has a stressstrain relationship that...Ch. 1 - On a graph, show the stressstrain relationship...
Ch. 1 - The rectangular block shown in Figure P1.11 is...Ch. 1 - The rectangular metal block shown in Figure P1.11...Ch. 1 - A cylindrical rod with a length of 380 mm and a...Ch. 1 - A cylindrical rod with a radius of 0.3 in. and a...Ch. 1 - A cylindrical rod with a diameter of 15.24 mm and...Ch. 1 - The stressstrain relationship shown in Figure...Ch. 1 - A tension test performed on a metal specimen to...Ch. 1 - An alloy has a yield strength of 41 ksi, a tensile...Ch. 1 - Prob. 1.21QPCh. 1 - Figure P1.22 shows (i) elasticperfectly plastic...Ch. 1 - An elastoplastic material with strain hardening...Ch. 1 - A brace alloy rod having a cross sectional area of...Ch. 1 - A brass alloy rod having a cross sectional area of...Ch. 1 - A copper rod with a diameter of 19 mm, modulus of...Ch. 1 - A copper rod with a diameter of 0.5 in., modulus...Ch. 1 - Define the following material behavior and provide...Ch. 1 - An asphalt concrete cylindrical specimen with a...Ch. 1 - What are the differences between modulus of...Ch. 1 - Prob. 1.33QPCh. 1 - A metal rod having a diameter of 10 mm is...Ch. 1 - What is the factor of safety? On what basis is its...Ch. 1 - Prob. 1.36QPCh. 1 - Prob. 1.37QPCh. 1 - A steel rod, which is free to move, has a length...Ch. 1 - In Problem 1.38, if the rod is snugly fitted...Ch. 1 - A 4-m-long steel plate with a rectangular cross...Ch. 1 - Estimate the tensile strength required to prevent...Ch. 1 - Prob. 1.42QPCh. 1 - Briefly discuss the variability of construction...Ch. 1 - In order to evaluate the properties of a material,...Ch. 1 - A contractor claims that the mean compressive...Ch. 1 - A contractor claims that the mean compressive...Ch. 1 - Prob. 1.47QPCh. 1 - Prob. 1.48QPCh. 1 - Prob. 1.49QPCh. 1 - Briefly discuss the concept behind each of the...Ch. 1 - Referring to the dial gauge shown in Figure P1.51,...Ch. 1 - Repeat Problem 1.51 using the dial gauge shown in...Ch. 1 - Measurements should be reported to the nearest...Ch. 1 - During calibration of an LVDT, the data shown in...Ch. 1 - During calibration of an LVDT, the data shown in...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- EXAMPLE 2.4. In an experiment, a steel specimen of 13 mm diameter was found to elongate 0.2 mm in a 200 mm gauge length when it was subjected to a tensile force of 26.8 kN. If the specimen was tested within the elastic range, what is the value of Young's modulus for the steel specimen ?arrow_forwardAnswer fastarrow_forwardA round steel alloy bar with a diameter of 19 mm and a gauge length of 76 mm was subjected to tension, with the results shown in Table P3.26. Using a computer spreadsheet program, plot the stress-strain relationship. From the graph, determine the Young's modulus of the steel alloy and the deformation corresponding to a 37 kN load. TABLE P3.26 Deformation, Load, kN mm 9 0.0286 18 0.0572 27 0.0859 36 0.1145 45 0.1431 54 0.1718arrow_forward
- Problem 24.16 It has been observed that the yield strength of the material of a component is normally distributed with a mean of 230 N/mm² and a standard deviation of 30 N/mm². The stress induced in the component is also normally distributed with a mean of 150 N/mm² and a standard deviation of 15 N/mm². Determine the reliability used in designing the component.arrow_forwardA solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing machine until the applied torque reaches the value T = 500 N •m. At this value of torque, a strain gage oriented at 45° to the axis of the bar gives a reading e = 339 × 10-6, What is the shear modulus G of the material? Strain gage Įd = = 50 mm T= 500 N-m T Round to one decimal place. GPa G =arrow_forwardPlease answer this question, An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the stress of each rod in MPaarrow_forward
- Fatigue test results of a material are shown in the diagram. a) Estimate the ultimate static strength of this material b) Estimate the fatigue (endurance) limit. c) If this test specimen has a cross-sectional area of 14 cm² and subjected to a maximum repeated load of 2800 kg over it, after how many repetitions will it fail? d) Determine the fatigue strength at 1000 cycles a (kgf/cm?) 500 400 300 200 100 2 3 4 5 6 logio Narrow_forward|Cycles to failure = 1E 3 Stress = 250 MPa 500 450 400 350 300 250 103 104 105 106 107 108 109 Cycles to failure Stress amplitude (MPa)arrow_forwardWarrow_forward
- A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm x 3.1 mm (0.7520 in. × 0.1220 in.) has the stress-strain behavior shown in the Animated Figure 6.22b. If this specimen is subjected to a tensile force of 98290 N (22100 Ib;) then (a) Determine the amount of elastic strain induced. (b) Determine the amount of plastic strain induced. (c) If its original length is 610 mm, what will be its final length after this force is applied and then released? The elastic modulus for steel is 207 GPa. (a) i (b) i (c) i mmarrow_forwardDURING THE STRESS-STRAIN TEST, THE UNIT DEFORMATION AT A STRESSOF 30 MPa WAS OBSERVED TO BE 110 x 10-6 mm/mm AND AT A STRESS0F 130 MPa IT WAS 520 X 10-6 mm/mm. IF THE PROPORTIONAL LIMITWAS 250 MPa, WHAT IS THE MODULUS OF ELASTICITY? WHAT IS THESTRAIN CORRESPONDING TO A STRESS OF 150 MPa?arrow_forwardA 220 mm? steel rod and 420 mm? copper rod supports a rigid bar as shown. If a 30 kN load is attached at the far end of the bar, determine the stresses in each of the rods. Based on the laboratory results, E= 200 GPa for steel and E= 100 GPa for copper. Show the free-body diagram. COPPER STEEL 2 m m- 2 m Hm- 30 kNarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning
Mechanical Properties of Material; Author: Civil Engineering;https://www.youtube.com/watch?v=UZkUvWiNeDs;License: Standard YouTube License, CC-BY