What problem is inherent in "stiff" systems? What happens when you try to solve the global system of equations? Draw a picture to show the correct support conditions that should be used in a structural FE analysis of the following situations: a. An office chair with rollers, loaded with the weight of one person. b. One shelf in a bookcase loaded with books. c. One shelf in a bookcase loaded with books. d. A flagpole cemented into the ground, analyzed using beam elements.

What problem is inherent in "stiff" systems? What happens when you try to solve the global system of equations? Draw a picture to show the correct support conditions that should be used in a structural FE analysis of the following situations: a. An office chair with rollers, loaded with the weight of one person. b. One shelf in a bookcase loaded with books. c. One shelf in a bookcase loaded with books. d. A flagpole cemented into the ground, analyzed using beam elements.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need right solution with clear calculations
Fundamentals of deformable bodies. Show the detailed answer. Thank you.
Example 8.3 A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when subjected to an axial load of 10 kN. The same specimen undergoes a twist of 0.5° and a length of 150 mm over a twisting moment of 10 N-m. Using the above data, determine the elastic constants E, H, G and K.
Figure 3a shows the loading, shear force diagram and bending moment diagram of a simply-supported beam with its cross-section shown in Figure 3b. Calculate the maximum bending stress in tension, the maximumbending stress in compression and the maximum shear stress in the beam.
The reinforced concrete considered in the figure below is subject to pure bending without any axial force. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 0.9ton.m . E, = 2*10ʻ kg / cm E = 222940kg /cm? f' = 225kg / cm F, = 4000kg / cm? 2 2 15 cm 20 cm 2#16 20 cm
Rock mechanics class appreciate your help and explanation
Show all step by step work
The block of wood glued together as shown is subjected to a compressive force of P KN. Determine P if the average normal stress, 50 MPa, is developed in the wood fibers oriented along the glued joint at 37° with the axis of the block. Dimension of block is given as a=48 mm, b=55mm. P Do not include units in final answer. Answer in 3 decimal places. b 2
A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 22 mm from the top of the beam on a section 3.41 m from A if P = 4661 N, W = 1614 N/m, a = 0.95 m, b = 1.94 m, c = 1.12 m, L = 72 mm and h = 184 mm. Round off the final answer to two decimal places. W P +² capita A с B inte b -c→ h
Explain
A wooden beam is loaded by a concentrated load P = 2000 N and supported by boundary conditions as shown in Figure Q5(a). The cross-section of the beam is shown in Figure Q5(b). Given that LAB = 2100 mm, LBC = 2900 mm, Bo=10 mm, B₁ = 20 mm, and H = 240 mm, ho=200 mm, h₁ =20 mm, determine the following quantities below:
A steel rectangular block, a = 2.4cm wide and b = 1.2 cm deep, is subjected to an axial tensile load as shown in the figure. Measurements show the block to increase in length by x=7.11×10-5m (initial length=10cm) and to decrease width by 8 z = 0.533×10-5m, when P is 45 kN. Calculate the modulus of elasticity and Poisson's ratio for the material. P