A stainless steel block with the dimensions shown in the figure has a density of 8000kg/m³. It is fixed at the top and carries an axial compressive load of 3kN at the bottom. Draw an average normal stress vs height diagram (use the conventional sign convention) for this block and calculate the maximum average normal stress acting in the block. Also, indicate the cross-section at which this stress is acting. Calculate the deflection of free end with respect to the fixed end (clearly indicate the direction)

A stainless steel block with the dimensions shown in the figure has a density of 8000kg/m³. It is fixed at the top and carries an axial compressive load of 3kN at the bottom. Draw an average normal stress vs height diagram (use the conventional sign convention) for this block and calculate the maximum average normal stress acting in the block. Also, indicate the cross-section at which this stress is acting. Calculate the deflection of free end with respect to the fixed end (clearly indicate the direction)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C P Steel: A=900 mm² E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the value of P without exceeding the allowable stress of bronze, in kN? 174 145 161 124
An aluminum pipe (modulus of elasticity 10.1x10^6 psi) is fixed at one end and is subjected to a tensile load of 127.5 kips at the free end. The length and cross-sectional area of the pipe is given as 36.1 in and 9.11 in^2. Assume that the aluminum pipe has clockwise torques (100 lb-in) acting at the midpoint and free end of the pipe. (a) Derive the element stiffness matrix
y A B 3 in. D C 2 in. -2 in. 1.5 in. E.
Mechanics of deformable bodies -Write complete solution
The beam shown in Fig QB1 is made from aluminium tube of rectangular cross-section having a vertical height of 50mm, a horizontal width of 30mm and a wall thickness of 3mm. The dimensions given in the figure are in millimetres. The yield stress in tension is 200MPa; Young's modulus is 71GPa. Determine: an expression for the bending moment at every point in the beam and draw the bending moment diagram a) b) c) d) the maximum bending moment the maximum longitudinal stress the maximum vertical deflection 200 3kN 200 1kN 100
A steel rod of 15- mm diameter is held snugly (but without any initial stresses) between rigid walls by the arrangement shown in the figure part (a). (For the steel rod, use α = 12 x 10-6/˚C and E = 200 GPa.) Calculate the temperature drop ΔT (degrees Celsius) at which the average shear stress in the 12 – mm diameter bolt becomes 45 MPa. Also, what is the normal stress in the rod? What are the average bearing stresses in the bolt and clevis at A and between the washer (dW = 20mm) and wall (t = 18 mm) at B? If the connection to the wall at B is changed to an end plate with two bolts (see figure part b), what is the required diameter db of each bolt if the temperature drop is ΔT = 38˚C and the allowable bolt stress is 90 MPa?
Need the correct handwritten solution , Don't make any mistakes
2. For the state of stress shown, determine the range of value of for which the normal is equal to or less than 100 MPa and 50 MPa. stress x' + 90 MPa 60 MPa =
1. If we take the stress function = 2x²y + xy², what are the stress components according to this stress function? What are the stresses on the boundaries of the body below? O y H H L X
For the beam structure shown below the data is as follows: P= 9.6-kN, L = 6-m, d= 2.4-m, b=100-mm, t-30-mm h=150-mm and h₁=130-mm. Neglect the self-weight of the beam. Based on this information answer the following question: Question 2.5: What is the maximum tensile stress in the beam? [Enter value in N and mm as appropriate] L B h
3. An ASTM A36 structural steel beam 5.00 m long is placed between two rigid supports. When the temperature is 20°C, there is no stress in the bar. Compute the stress developed in the beam if the temperature rises to 45°C. Assume that the proportional limit is 235 MPa. a = 11.7 x 10-6 1/C° E = 207 GPa 4. In question 3, assume that the bar is free to elongate or shorten, calculate the change in the length of the bar if the temperature drops from 20°C to -20°C.