For the beam structure shown below the data is as follows: P= 9.6-kN, L = 6-m, d= 2.4-m, b=100-mm, t-30-mm h=150-mm and h₁-130-mm. Neglect the self-weight of the beam. Based on this information answer the following question: Question 2.5: What is the maximum tensile stress in the beam? [Enter value in N and mm as appropriate] B 111 h

For the beam structure shown below the data is as follows: P= 9.6-kN, L = 6-m, d= 2.4-m, b=100-mm, t-30-mm h=150-mm and h₁-130-mm. Neglect the self-weight of the beam. Based on this information answer the following question: Question 2.5: What is the maximum tensile stress in the beam? [Enter value in N and mm as appropriate] B 111 h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 52-kip force acts on a machine part at point A as shown below. The diagram shows the internal normal force, shear force and bending moment acting on a particular RECTANGULAR Cross section. -30in N 10in 26in F=52 kip The value of the bending moment M you would use to find the bending stress on a stress element located 2 inches up from the bottom of the rectangular cross section is closest to: 264 kip-in O a. 408 kip-in Ob. 1,464 kip-in O c. 1,608 kip-in
SOLID MECHANICS
Need step by step
I need right solution with clear calculation.
Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph. The data for Pv, Ph, a,L,and e are shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 80k N a = G0o 6 omm e %3D 26 K N 120 mm L =3600 mm Figure 1 250 mm
Question 3 A pair of lateral load is applied to a 3 m steel beam as in Figure Q3a to bend it plastically. The beam has a solid rectangular cross-section (30mm x 50mm) as in Figure Q3b. The steel behaves in elastic-perfectly plastic behavior with Yield Stress of 200 MPa. When 50% plastic condition at critical section, determine: a. the value of load P b. the Yielded Length, Lp corresponding to condition in part (a). 1.5P P 1m 1m Figure Q3a 1m 30mm 50mm Figure Q3b
A steel wire (E = 200 GPa) of diameter d = 1.0 mm is bent around a pulley of radius Ro= 400 mm (see figure below). Ro a. What is the maximum stress in the wire? b. Does the stress increase or decrease if the radius of the pulley is increased?
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.72 mm the values of elastic modulus for steel is 223 MPa. Take H1 = 7 cm, H2 = 10 cm, top bar (R) is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = ii) Stress-induced in the top bar = iii) Stress-induced in the bottom bar =
Thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure.[a = 200 mm, b = 202.1 mm, c = 198.9 mm] For the deformed plate, determine the normal strain of diagonal PR? In micro £ For the deformed plate, determine the shear strain xy at corner P?in micro rad
For P = 100 MPa, determine the range of values of τxy for which the maximum tensile stress is equal to or less than 60 MPa. (Round the final answer to one decimal place.)
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1300 mm, and the height of the plate is h = 1700 mm. The shear strain at A is known to be +4172 μrad. Assume a = 2.9 mm. Calculate the magnitude of dimension b in the figure.
Please Help me