Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.7 GPa. Bar (2) is a nylon material that has an elastic modulus c 0.9 GPa. Each bar has a cross-sectional area of 1350 mm². Using L = 355 mm and A = 6.3 mm, what magnitude of load P will cause the normal stress in each bar to be the same value? a a L (1) Answer: P = i B (2) (1) KN

Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.7 GPa. Bar (2) is a nylon material that has an elastic modulus c 0.9 GPa. Each bar has a cross-sectional area of 1350 mm². Using L = 355 mm and A = 6.3 mm, what magnitude of load P will cause the normal stress in each bar to be the same value? a a L (1) Answer: P = i B (2) (1) KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the state of stress as shown in figure. What will be the principal stresses? 02= 16Mpa oy= – 48 M pa, Try = 60 Mpa T 48 Mpa + 16 Mpa 60 Mpa
2. Shown below are pieces of unsaid material. They are combined and locked in each other and a force P is pulling each side. Assuming that the Shear stress for the material is 38 MPa, Determine the force P needed to fracture the materials in shear. 30 mm 30 mm 80 mm Section A-A
1. For each state of plane stress shown below, i.e., for configurations (a) and (b), indicate whether each component of the state of strain is: = 0 (equal to zero) >0 (greater than zero) <0 (less than zero) The material is linear elastic with Possion's ratio is between (0, 0.5), and the deformations are small. T 30 e X 0 Ex Ey Ez Yxy Yyz Yzx (a) (b) 1° (b) 1x
A steel wire (E= 200 GPa) of diameter d= 1.25 mm is bent around a pulley of radius Ro= 500 mm. What is maximum stress in the wire?
ox The state of stress at a given point in a material component is = 120 MPa; Oy = - 80 MPa and t = 60 MPa The loading on the component is increased so that stresses are increased to values which are k times the given values. Determine the maximum value of k if the material can withstand maximum normal and shear stresses of 300 MPa and 200 MPa respectively. 1 11
ANSWER THE PROBLEM GIVE WHAT IS ASKED, SHOW YOUR SOLUTION, AND BOX THE FINAL ANSWERS. WRITE IT ON A CLEAN PAPER CLEARLY. I WILL GIVE THE FEEDBACK RATING AS POSSIBLE, YOU CAN ANSWER IT. THANK YOU
Question- Principal stress at a point in an elastic material are 1.50 (tensile), o (tensile) and 0.50 (compressive). The elastic limit in tension is 210 MPa and poisson's ratio=0.3. Find the value of o at the failure when computed by the maximum principal strain theory.
At a point on the surface of a machine component the stresses acting on the e face of a stress element are or = 55 MPa and Txy = 30 MPa (see figure). T- 30 MPa a, = 55 MPa What is the allowable range of values for the stress oy if the maximum shear stress is limited to TO = 34 MPa? Round to one decimal place. (a) Lower limit is MPa (b) Upper limit is MPa
A steel wire (E = 200 GPa) of diameter d = 1.0 mm is bent around a pulley of radius Ro= 400 mm (see figure below). Ro a. What is the maximum stress in the wire? b. Does the stress increase or decrease if the radius of the pulley is increased?
2. A copper rod of diameter 12 mm is subjected to a compressive force of 8 kN. The change in diameter happens to be 4.5 x 103 mm. Determine the strain along the length of the material and the Poisson's ratio when E = 110 GPa.