A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1450 mm,and the height of the plate is h = 2100 mm.The shear strain at A is known to be +3232 urad. Assume a = 2.2 mm. Calculate the magnitude of dimension b in the figure.DAnswer:b = iWBammX

Shear strain is the ratio of displacement to an object's original dimensions due to stress, and is…

A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1450 and the height of the plate is h = 2100 mm. The shear strain at A is known to be +3232 urad. Assume a = 2.2 mm. Calculate the magnitude of dimension b in the figure. D k Answer: b= i W B a mm X

A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1450 and the height of the plate is h = 2100 mm. The shear strain at A is known to be +3232 urad. Assume a = 2.2 mm. Calculate the magnitude of dimension b in the figure. D k Answer: b= i W B a mm X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Thanks for the help
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.72 mm the values of elastic modulus for steel is 223 MPa. Take H1 = 7 cm, H2 = 10 cm, top bar (R) is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = ii) Stress-induced in the top bar = iii) Stress-induced in the bottom bar =
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 480 psi in size. (a) Determine the stresses o,, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). y
Thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure.[a = 200 mm, b = 202.1 mm, c = 198.9 mm] For the deformed plate, determine the normal strain of diagonal PR? In micro £ For the deformed plate, determine the shear strain xy at corner P?in micro rad
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1300 mm, and the height of the plate is h = 1700 mm. The shear strain at A is known to be +4172 μrad. Assume a = 2.9 mm. Calculate the magnitude of dimension b in the figure.
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 520 psi in size. (a) Determine the stresses o, Oy, and the magnitude of Ty and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). Answer: (a) ox = psi Oy = psi Txy = psi (b) Op1= psi Op2 = psi Tmax in-plane psi
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = 60 MPa, o, = 110 MPa, and Txy = 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components &x, y, z, and Yxy. Assume that E = 73 GPa and v=0.29 for the machine component. £x = que 11 Ox Ez = με με με μrad
Figure Q4 shows a piece of triangular thin plate ABC with thickness 5 mm. A linear pressure as shown in the figure is being applied to edge AB with maximum intensity of 100 kN/m² at the middle of edge AB. The plate is made from stainless steel, with a Young's modulus of 200 GPa and Poisson's ratio of 0.3. The deformations in the plate are to be obtained. For such purposes, the finite element method is being employed. (a) (b) (c) (d) (e) State the type of problem involved in this case (to determine the stiffness matrix to be used). Model this problem optimally using the least number of orthogonal triangular elements only. Label the nodes and elements and indicate clearly the status of all the relevant degrees-of- freedom in this model. Set up the appropriate system of simultaneous equations and solve for the unknown displacements. Displacements at point T. Without any calculation, explain on the value of strain at points S and T.
xy=53
ANSWER THE PROBLEM QUESTION AND SHOW YOUR SOLUTION CLEARLY AND BOX THE FINAL ANSWER. USE 2 DECIMAL PLACES
Use stress transformation method and not the equations.
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 320 psi in size. (a) Determine the stresses Ox, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). X D C y b