Two simply supported beams are made up of the same material and are of the same cross-section. Both beams carry uniformly distributed loads of equal intensities. One beam is 2 m long and the other is 4 m long. The 2 m long beam shows a central deflection of 1 mm. What is the central deflection of the 4 m long beam? (a) 16 mm (b) 2 mm (c) 8 mm (d) 1 mm

Two simply supported beams are made up of the same material and are of the same cross-section. Both beams carry uniformly distributed loads of equal intensities. One beam is 2 m long and the other is 4 m long. The 2 m long beam shows a central deflection of 1 mm. What is the central deflection of the 4 m long beam? (a) 16 mm (b) 2 mm (c) 8 mm (d) 1 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Asap need correct
Please help me answer completely each problem and box the final answer. Thanks for helping me.
0/10 FIND DEFLECTION IN Aluminum. IF E st= .200000 MPa, Ealu.=70000 MPa 100 kN R ALU.=30 MM Aluminum Steel 0.4 mm 2 mm 0.5 mm 0.25 mm no one 1m_ RST = 20 MM
AW14x22 beam is subjected to a moment of 99 ft-kips. What is the bending stress in the beam in psi? Type your answer...
A 4-cm-OD, 3-cm-ID, circular shaft supports a 200 N load and is supported at two points, which are 2-m apart as shown here. What is the radius of curvature of the bending shaft when it is made of a material whose modulus of elasticity is 50 GPa?
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3.5 cm and internal diameter 2.4 cm The modulus of elasticity for the material is 210 x 109 N/m². Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.7 cm from the neutral axis Solution: (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is iv) The bending stress at the point 0.7 cm from the neutral axis is
Given the 180 mm x 360 mm rectangular beam as shown in the figure. 100 kN/m 20 kN-m 50 kN/m 360 mm 1.5 m 5 m 180 mm What is the bending or flexural stress in a fiber 20mm from the top of the beam at the left support in MPa?
Aluminum [E = 72 GPa] member ABC supports a load of 31 kN, as shown in the figure. Determine (a) the value of load P such that the deflection of joint C is zero. (b) the corresponding deflection of joint B (positive if B moves up and negative if down). 1.0 m 1.3 m 31 KN C 34-mm diameter B 52-mm diameter
A concrete beam pre-stressed with a parabolic tendon is shown in the figure. The eccentricity of the tendon is measured from the centroid of the cross-section. The applied pre-stressing force at service condition is 1620 kN. The uniformly distributed load of 85 kN/m includes the self weight of beam. 85 kN/m 500 mm 750 mm 145 mm 6 m The net deflection at the mid-span of the beam will be [Grade of concrete used is M35]
A simply supported beam 3 meters long has a cross-section as shown in figure (i). The beam carries two loads of equal magnitude as shown in figure (ii). If the maximum compressive and tensile stresses are not to exceed 100 N/mm² and 120 N/mm² respectively, determine the maximum value of W. 80 mm 60 mm 120 mm 160 mm (i) Cross-section diagram W 1m 1m 1m 3 m W (ii)
the cantilever has a partially hollow circular cross section. If the admissible normal stress is 140 MPa, determine the maximum value of Wo (distributed load intensity) that the beam can support. express your answer in KN / m
Help me friend