An artificial humorous bone is used in human body as shown in figure 3 below. it is supported by scapular joint at A and artificial tendon made from flexible material at C. This humorous bone makes an angle (20° with tendon and it is connected to forearm at B by elbow joint. The forearm carries load of 70 Kg as shown. According to this simplified case, determine the maximum EIY [deflection] in the humorous bone knowing that this bone has a circular cross-sectional area with 10 mm radius. Fore-armi B 180 mm 120 mm 70 Kg C A Artificial tendon Figure 3.

An artificial humorous bone is used in human body as shown in figure 3 below. it is supported by scapular joint at A and artificial tendon made from flexible material at C. This humorous bone makes an angle (20° with tendon and it is connected to forearm at B by elbow joint. The forearm carries load of 70 Kg as shown. According to this simplified case, determine the maximum EIY [deflection] in the humorous bone knowing that this bone has a circular cross-sectional area with 10 mm radius. Fore-armi B 180 mm 120 mm 70 Kg C A Artificial tendon Figure 3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

A: given- 2 simply supported beams-same material and same cross-sectionSame UDLspan of beam=2 m and 4…

Q: The rigid bar BDE is supported by two links All and CD. Lank All is made of steel (E200 GPa) and has…

Q: Q31 For the beam shown in Fig. (3); ( El is constants ): A-Compute the slope of the elastic curve…

A: Given overhang beam .. Slope and deflection at particular specified points can be calculated by…

Q: A tapered circular rod of diameter varying from 20 mm to 10 mm is connected to another uniform…

Q: An 8-m simply supported beam AB carries a downward 8-kN point load located 6 m from the left support…

Q: An 8m long steel column is pinned at the top and fixed at the bottom. The column is provided with…

A: Given: The length of the column is 8 m. The lateral support is at 3 m from the top. The value of Ix…

Q: A steel column is supported at the top by two steel rods so as to prevent movement at the top in the…

A: The effective length of the column depends upon its Fixed end condition. Here, in this case, one end…

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

Q: The piece of rubber is originally rectangular. Calculate the average shear strain Yxy at A if the…

Q: A horizontal rigid bar of negligible mass is binged at one end, Fig.1, and supported by a bronze rod…

A: Given data: Steel:A=600 mm2, E=200 GPaBronze:A=300 mm2, E=83 GPa

Q: A telescope with tripod weighs 25 pounds and has geometry as shown in the figure and parameter…

Q: A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂…

A: G = 10.93 MPaP = 13 kN or 13000 N

Q: The gusset plate is subjected to the forces of three members as shown in (Eigure 1). The forces are…

A: Consider vertical force equilibrium9 - 6sin - Tsin = 09 - 6* - Tsin = 0Tsin = 5.4 ...equation…

Q: The truss shown supports an automobile which has a mass of 2000 kg. Each member of the truss has…

Q: Q1b For the pin-jointed frame in Figure Q1b, (i) State whether the frame is in statistically stable…

Q: A cantilever beam of solid circular cross section is 1 m long and has a diameter of 100 mm. Attached…

A: D = Diameter = 100 mm = 0.1 mL = Length of beam = 1 m

Q: The truss shown in the figure below is made from A992 steel rods having a diameter of 30 mm and…

Q: The beam has a rectangular cross section and is made of and elastic-plastic material having a stress…

Q: Deflection Given: the beam cross-section shown have the following cross-sectional properties f'c…

Q: Help me pls

A: Since you have asked multiple question, we will solve first question for you.If you want any…

Q: Problem 2 A rigid bar, hinged at one end, is supported by two identical springs as shown in Fig.…

Q: on 333. A member has a cross section as shown in the Figure. The second moment of area (inertia) of…

Q: The force applied at the handle of the rigid lever as shown in figure 1 causes the lever to rotate…

A: The lever arms rotates through an angle of Since - is small A,C,D can be approximatedCalculate the…

Q: -- A thin aluminum plate profile hown in the accompanying igure is subjected to an axial oad.…

A: Considering the section below:

Q: Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A…

Q: (a) Calculate the magnitude of force G. given that the maximum normal stress in each member should…

Q: Determine the force in the member CD of the truss and state whether it is in tension or compression…

A: At Joint C,

Q: From the given Figure and data below. Determine the a. P so that the structure is stable (in…

Q: what is the value of the maximum NEGATIVE bending moment acting on this beam

Q: Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A…

Q: A beam carries a concentrated load W and a total uniformly distributed load of 4W as shown in the…

A: Given data Permissible tension stress = 80 MPa Permissible compression stress = 120 MPa

Q: 12. The concrete table column-support in Problem 20is reinforced with three -in steel rods, as shown…

Q: The force applied at the handle of the rigid lever as shown in figure 1 causes the lever to rotate…

A: The lever arms rotates through an angle of θ θ=2oπ180radθ=0.03491 rad Since θ- is small A,C,D can…

Q: For the structure and loading shown below, find the lateral deflection at the top. Use E = 29,000…

Q: Two carbon plates are bonded to the upper and lower surfaces of a wooden beam. The beam is simply…

A: L= 900 mmb =20.5 mmw = 65 N/mmEw= 23 Gpa or 23000 MPaEc =102 Gpa or 102000 MPa

Q: B.1 A high performance racing plane is to have an aileron control rod made out of unidirectional…

Q: Which of the following expressions gives the distance from the free end where the beam will break?…

Q: E 600 mm D |P 400 mm A B - 600 mm- 600 mm- If the applied force P causes the rigid arm ABC to rotate…

Q: A steel column is supported at the top by two steel rods so as to prevent movement at the top in the…

A: Kx, Ky, and K are the effective length factors of compression members or columns. Mathematically,…

Q: In analyzing or designing trusses, it is necessary to determine the force in each member o the…

Question

Q3/
An artificial humorous bone is used in human body as shown in figure 3 below. it is
supported by scapular joint at A and artificial tendon made from flexible material
at C. This humorous bone makes an angle (20° with tendon and it is connected to
forearm at B by elbow joint. The forearm carries load of 70 Kg as shown. According
to this simplified case, determine the maximum EIY [deflection] in the humorous
bone knowing that this bone has a circular cross-sectional area with 10 mm radius.
w=70
Fore-ar
B
180 mm 120 mm
70 Kg
C
A
Artificial tendon
Figure 3.
dy
do
te

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:-

VIEW

Step 2: Force in tendon:-

VIEW

Step 3: Moment equation:-

VIEW

Step 4: Boundary conditions:-

VIEW

Step 5: Maximum deflection:-

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 14 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The equation of deflected shape of beam carrying uniformly distributed load on a simply supported beam is given by, Which of the following statement is correct for the given beam? A Total length of beam is 12 m B Total length of beam is 24 m C Load intensity on beam is 8 kN/m D Load intensity on beam is 4 kN/m
Figure 4–5a shows a cantilever beam with an end load. Normally we model thisproblem by considering the left support as rigid. After testing the rigidity of thewall it was found that the translational stiffness of the wall was kt force per unitvertical deflection, and the rotational stiffness was kr moment per unit angular(radian) deflection (see Fig. 4–5b). Determine the deflection equation for the beamunder the load F.
1. A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques as shown in Fig. P-316. Determine the maximum permissible value of T subject to the following conditions: Tst < 83 MPa, tal < 55 MPa, and the angle of rotation of the free end is limited to 6°. For steel, G = 83 GPa and for aluminum, G = 28 GPa. Steel 2T Aluminum 50 mm Ø 40 mm Ø 900 mm 600 mm
The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and σ = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
4. The simply supported wood beam ABC in Fig. Q4 has a rectangular cross section and supports a concentrated load of 300 N. Calculate the maximum deflection of the beam. The modulus of elasticity for the beam is given as E= 12 GPa. 300 N B A ·X 80 mm 2 m RA= 100 N Rc = 200 N 1.0 m- Fig. Q4 40 mm
Problem 5 The load has a weight of 950 lb. -1.5 ft- 1 in. max = Section a - a Q Tap image to zoom Part A Determine the maximum normal stress developed on the cross section of the supporting member at section a-a. Express your answer in kilopounds per square inch to three significant figures. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: ksi
Q2/ For the two cases shown in Fig.2 (EI is constant) and by using unit load method, compare between the two cases according to the maximum deflection and show whom is the best loading that you think P= W*L 5 Marks Figure (2 B Case (1) Case (2)
For the following cross section determine: a) Iz and Iy b) Yield and plastic moments (My and Mp) for bending about z axis only c) Shape factor for bending about the z axis only d) The moment that causes yielding to extend 30 mm into the section from the top flange and bottom flange into the web (bending about z axis only) Given:E = 200 GPa, σy = 400 MPa
Determine the angle of twist between A and C for the brass shaft loaded as shown in Fig. 9.6.3. Take G = 40 GPa and %3D diameter of shaft = 40 mm.?? 400 Nm 1200 Nm 800 Nm A •B C. 1 m 1.5 m Fig. 9.6.3
A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE, that exert uniformly distributed upward loads as shown. Determine the values of wec and WDE corresponding to equilibrium when WA = 750 N/m. 1200 N/m 20 C WBC ADA A 0.6 m- B' 0.8 m The value of WDE is The value of wBc is [ -3.1 ms -6 m- N/m. N/m. D (DE 1.0m E F
As a construction engineer, you are asked to evaluate the maximum allowable vertical shear Vmax that may act on the hollow stainless-steel beam having a rectangular cross section as shown in Figure Q4. Discuss the effect of geometry on the shear stress developed in the beam | 20 mm y 350 mm V 10 mm- -10 mm 1 30 mm E 200 mm
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm