Consider a point in a structural member that iS subjected to planestress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of S-30 MPa, Sy= 220 MPa. Construct Mohr's circle for this state of stress on paper anduse the resultsto answerthe questions in the subsequent parts of this GO exercise. For this Mohr's circle, point x, which representsthe state of stress onthexface ohestress element, should appear: O Above and to the right of thedircle centen O Above and to the left of the circle center. O Below and to the left of thecirclecenter O Below and to the right of the circle center.

Consider a point in a structural member that iS subjected to planestress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of S-30 MPa, Sy= 220 MPa. Construct Mohr's circle for this state of stress on paper anduse the resultsto answerthe questions in the subsequent parts of this GO exercise. For this Mohr's circle, point x, which representsthe state of stress onthexface ohestress element, should appear: O Above and to the right of thedircle centen O Above and to the left of the circle center. O Below and to the left of thecirclecenter O Below and to the right of the circle center.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
For the beam shown below, b = 5 in and h = 12 in. If the beam is subjected to a transverse shear for of V = 8 kip, determine the largest shearing stress in the beam. Express your answer in psi to the nearest whole psi
Show complete solution, include necessary figures. The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension.A. Draw the Mohr's circle for this stress combination.B. What is the maximum shear stress acting at the point and what value of normal stress acts on the plane?C. Determine the value of the normal and shear stress acting on a plane that is 30 degrees from the minor principal plane.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sy = 100 MPa and Sy = 215 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume ß = 51°. ↑ Answer: Sn = MPa Snt = MPa
The stresses shown act at a point in a stressed body. The stress magnitudes are Sy = 95 MPa and Sy = 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 55°. Sy Answer: Sn = MPa Snt = MPa
Question The state of 2D-stress at a point is given by the following matrix of stress: [0x %]-[ 100 30 30 20 = MPa 0. What is the magnitude of maximum shear stress(Radius of Mohr's circle) in MPa?
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S, = 8.0 ksi, S, = 10.5 ksi, and Sxy = 8.0 ksi. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point. Sy Sxy S.
Give me right solution with clear calculations.
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A?in micro rad Determine the shear strain γnt at point A?in micro rad What is the normal strain in the x-direction?micro£
www The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and Sy = 210 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume 3 = 47° Selle Answer: Sn = Snt = S, 6 ← T 5 S., MPa MPa
The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 100MPA and S, = 245 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 55°. Sy Answer: Sn = MPa Snt = MPa
need help with assignment thankss....(especially the mohrs circle part for the graph) x=4, y=4, A=13