The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at = 31.0.a= 5, and b = 3. Using the equilibrium equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and r(magnitude only) at the point are S, = 26 MPa, S, = 45 MPa, and Sy = 26 MPa. Assume = tan-' this point on the inclined plane shown. Answers: MPa, r= MPа.

The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at = 31.0.a= 5, and b = 3. Using the equilibrium equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and r(magnitude only) at the point are S, = 26 MPa, S, = 45 MPa, and Sy = 26 MPa. Assume = tan-' this point on the inclined plane shown. Answers: MPa, r= MPа.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The curved bar shown in the figure has a rectangular cross section of 50x75 mm and an internal radius of 125 mm. For a force F = 1200 N, determine: a-) the normal stress at point A. b-) the normal stress in point B.
View Policies Current Attempt in Progress The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy = 20 MPa, Sy = 40 MPa, and Sy = 26 MPa. Assume ß = tan- = 31.0°, a = 5, and b = 3. Using the equilibrium equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and t (magnitude only) at this point on the inclined plane shown. Sxy Answers: O = MPa, T = i MPа.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sy = 100 MPa and Sy = 215 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume ß = 51°. ↑ Answer: Sn = MPa Snt = MPa
Figure 1 shows the elastically deformed shape AB'C'D' of a thin plate subjected to plane stress conditions. The elasticity modulus and Poisson's ration are E=210 GPa and v=0.33 respectively. Determine the direction (angle 0) of the maximum shear stress on the point 0(0.5, 0.5). C'(1.09, 1.08) D'(0.01, 1.03) C(1.00, 1.00) D(0, 1) A(0, 0) O(0.5, 0.5) B(1, 0) B'(1.05, 0.06)
The stresses shown act at a point in a stressed body. The stress magnitudes are Sy = 95 MPa and Sy = 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 55°. Sy Answer: Sn = MPa Snt = MPa
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S, = 8.0 ksi, S, = 10.5 ksi, and Sxy = 8.0 ksi. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point. Sy Sxy S.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, = 220 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 51°. S ↑ Answer: Sn = MPa Snt = MPа
Consider the state of plane stress shown. (Hint: Consider both in-plane and out-of-plane shearing stresses.) 7 ksi Determine the maximum shearing stress when ox- 18 ksi and ay = 8 ksl. The maximum shearing stress is ksi.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and Sy = 215 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 50°. Sx
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume'stress magnitudes of 5,-80 MPa, S - 220 MPa. Sy For the given state of stress at a point in a structural member, determine the center Cand the radius R of Mohr's circle. Answers: C- MPa, R- i MPa. Save for Later Part 3 Determine the principal stresses (api > Op2 ) for this state of stress. Answers: Opl = MPa, o,2 = MPa Save for Later Part 4 For this Mohr's circle, determine the magnitude of the central angle between: (a) pointxand the point representing the principal stress opl- (b) point x and the point representing the principal stress Op2. (a) Angle - i (b) Angle - i
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx= 100 MPa, σy= 65 MPa, and τxy= 70 MPa, acting in the directions shown in the figure. At this point, determine the strain components εx, εy, εz, and γxy. Assume that E = 71 GPa and v = 0.28 for the machine component.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 2200 psi, Sy = 2000 psi, and Sy = 3400 psi, acting in the directions indicated in the figure. Determine the normal and shear stresses at this point on the inclined plane shown. Assume ß = 46°. Sxy S. Answer: Sn i psi Snt = psi