Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 16 MPa in the direction shown, determine the principal stresses at the point. 10 MPa 26 MPa O 35.56 MPa and -14.11 MPa 54.80 MPa and -17.81 MPa O 27.65 MPa and -9.78 MPa O 46.71 MPa and -11.05 MPa O 39.17 MPa and-13.17 MPa

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 16 MPa in the direction shown, determine the principal stresses at the point. 10 MPa 26 MPa O 35.56 MPa and -14.11 MPa 54.80 MPa and -17.81 MPa O 27.65 MPa and -9.78 MPa O 46.71 MPa and -11.05 MPa O 39.17 MPa and-13.17 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

9. The initially square element of a material is deformed as shown. Determine the shear strain of the element and the normal strains of the diagonals AC and BD. Undeformed Deformed A B D 2.0 mm 2.015 mm C 1.995 mm
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 68 MPa, determine the principal stresses acting at the point. 114 MPa 66 MPa 157.9 MPa and -155.4 MPa 82.0 MPa and -83.7 MPa O 121.2 MPa and -138.0 MPa O 167.4 MPa and -98.1 MPa O 133.2 MPa and -131.2 MPa
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 25 MPa in the direction shown, determine the principal stresses at the point. 28 MPa 16 MPa O 39.2 MPa and -30.2 MPa O 31.6 MPa and -35.8 MPa 54.1 MPa and -41.3 MPa 35.8 MPa and -27.4 MPa O 27.7 MPa and -39.0 MPa Save for Later eTextbook and Media Attempts: 1 of 3 used Submit Answer
1. The member is loaded as shown. The diameter of the member is 32 mm. 1) Calculate all internal loadings on the cross section through the point A. 2) Calculate the stress at point A due to each internal loading. 0.4 m A Rigid Wall 1000 N 300 Nm 2000 N
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If σ = 11 MPa in the direction shown, determine the principal stresses at the point. 28.6 MPa and -33.6 MPa 20.7 MPa and -42.4 MPa 39.6 MPa and -46.7 MPa 26.8 MPa and -35.8 MPa 34.2 MPa and -40.0 MPa
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Let T = 39 MPa and o = 19 MPa. Determine the center ocenter of the corresponding in- plane Mohr's circle. 50 MPa -21.56 MPa O -17.85 MPa O -10.87 MPa -14.07 MPa -15.50 MPa
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A?in micro rad Determine the shear strain γnt at point A?in micro rad What is the normal strain in the x-direction?micro£
Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB?in micro rad And answer in right and clear way Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, = 220 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 51°. S ↑ Answer: Sn = MPa Snt = MPа
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
Steel plate (2) b. 4. Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. a. 8.5 ksi 5.7 ksi 10.5 ksi Draw Mohr's circle for this state of stress. Me grapting page is ba b. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Ans. c. Show these stresses on an appropriate sketch. <
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume'stress magnitudes of 5,-80 MPa, S - 220 MPa. Sy For the given state of stress at a point in a structural member, determine the center Cand the radius R of Mohr's circle. Answers: C- MPa, R- i MPa. Save for Later Part 3 Determine the principal stresses (api > Op2 ) for this state of stress. Answers: Opl = MPa, o,2 = MPa Save for Later Part 4 For this Mohr's circle, determine the magnitude of the central angle between: (a) pointxand the point representing the principal stress opl- (b) point x and the point representing the principal stress Op2. (a) Angle - i (b) Angle - i