The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are $x = 16.5 ksi, $y = 2.5 ksi, and Sxy= 7.2 ksi. Assume = 20°. Determine the normal stresses σ, and oy and the shear stress Txy at the point. Answers: 0x = Oy = Ivi = Ty Txy ksi. ksi. ksi.

The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are $x = 16.5 ksi, $y = 2.5 ksi, and Sxy= 7.2 ksi. Assume = 20°. Determine the normal stresses σ, and oy and the shear stress Txy at the point. Answers: 0x = Oy = Ivi = Ty Txy ksi. ksi. ksi.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

QUESTION 3. The state of plane stress at a point on the tail of Turkey National Combat Aircraft is shown in the figure. Applying both analytical method and the Mohr's cicle, determine a. Determine principal stress values b. Calculate the maximum inplane shear stress and average normal stress. c. Draw the element location for each condition. d. Determine the absolute maximum shear stress value at the same point. 40 MPa TAI 200 MPa 80 MPa
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = 80 MPa, o, = 20 MPa, and Try = 70 MPa, acting in the directions shown in the figure. ox At this point, determine the strain components £, £y, E, and Yay.. Assume that E-70 GPa and v- 0.30 for the machine component. Ex = με Ey = не E₂ = Yxy = με μrad
M=48 MPa N=-7 MPa txy=20 MPa theta=25 degrees
. The biaxial stress system in an element is shown in the figure. Which of the following will give the normal stress in N/mm2 in the plane BD making an angle of 45° with the plane BA? 2 0₁ = 60 N/mm² C 0₂ = = 40 N/mm A A A 0₂ = = 40 N/mm 2 45 2 A B On 2 0₁ = 60 N/mm
For the state of stress given in the illustration below, determine the normal and shear stresses on plane A. = -29000 psi A 20° T xy 8 = 7250 psi = 11600 psi
The normal and shear stresses at a point in a structural subjected to a state of plane stress are shown in figure below. Determine using stress transformation equation or Mohr's circle. i) principal stresses and their directions. ii) maximum shearing stress and its direction. iii) stress on a plane making an angle of 30° anticlockwise from plane AD. [Ans: i) o1 = 33 MPa, o2 = -23 MPa, O, = 68°, ii) Tmax = 28 MPa, O, = 22.5°, iii) o = 12.5 MPa, Gy = -2.32 MPa, tay = 27.3 MPa] 25 N/mm? B 20 Nmm 30 15 Nmm?
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 240 psi in size.(a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element.(b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16).
Completely solve. WRITE LEGIBLY OR TYPEWRITE THE SOLUTIONS. USE 3 DECIMALS. BOX THE FINAL ANSWERS.
2
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 360 psi in size. (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16).
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 25.7 ksi, Sy= 3.7 ksi, and Sxy= 6 ksi. Assume ß = 38°. Determine the normal stresses o, and o, and the shear stress Txy at the point. Sx Txy Answers: 0x = Oy = Txy = ox B ksi. ksi. ksi.
hand written solution pls