Example 7.9 At a point in an elastic material, 0, 40 Nimm a direct tensile stress of 80 N/mm? and a direct compressive stress of 40 N/mm2 are applied on planes at right angles to each other. If the maximum principal stresses are limited to 100 N/mm2 (tensile). Find the shear stress that may be o, = 80 N/mm allowed on the planes. Also, determine the minimum principal stresses and maximum shear stress ()

Example 7.9 At a point in an elastic material, 0, 40 Nimm a direct tensile stress of 80 N/mm? and a direct compressive stress of 40 N/mm2 are applied on planes at right angles to each other. If the maximum principal stresses are limited to 100 N/mm2 (tensile). Find the shear stress that may be o, = 80 N/mm allowed on the planes. Also, determine the minimum principal stresses and maximum shear stress ()

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 25.7 ksi, Sy= 3.7 ksi, and Sxy= 6 ksi. Assume ß = 38°. Determine the normal stresses o, and o, and the shear stress Txy at the point. Sx Txy Answers: 0x = Oy = Txy = ox B ksi. ksi. ksi.
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A? Determine the shear strain γnt at point A? In micro rad What is the normal strain in the x-direction? What is the normal strain in the y-direction? What is the normal strain in the n-direction? Answer in clear way please
Steel Tank with an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used as storage of gas under pressure of 2.2 MPa. a. Determine the value of the tangential stress in the tank wall Determine the value of the longitudinal stress in the tank wall b. 30 mm helt hand
2. The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. 0.75 m 1.5 m A B Steel A = 250 mm? E = 200 GPa Aluminum L= 2 m A = 300 mm? E = 70 GPa D
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are 5x = 19.6 ksi, 5y = 4.3 ksi, and Sxy= 7.3 ksi. Assume ß = 38°. Determine the normal stresses ox and 6, and the shear stress Txy at the point. Say Sx Txy Answers: 0x = oy = Txy || ox ksi. ksi. ksi.
Q: A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm2 stress.
B3
I need the answer as soon as possible
4. A uniform bar with an area of o.25 in- is pulled between two points. The tensile force at a temperature of 21.11°C is 1200 lb. What will be the stress at -17.78°C? At what temperature will the stress be zero? Assume a = 6.5 × 106 in/(in-°F) and E = 29 × 10ʻ psi. %3D %3D
I need the answer as soon as possible
Please solve quick