What is the minimum distance from the holes at each end of the part? - 2x Ø 1.375-1.390 +Ø010 LABC 2x Ø.010 @ LMC Tolerance zones 2.000-2.020 1.000

Q: 14. What size internal chamfer is required for the part? 14. 15. Why does the flatness tolerance not…

A: 15. Why does the flatness tolerance not reference a datum

Q: A metal disc of 20mm diameter is to be punched from a sheet of 2mm thickness. The punch and the…

A: Given operation is blanking operation. Blank operation  = D = 20 mm Sheet thickness = t = 2mm…

Q: Specify a cylindricity tolerance of .0004 for the largest cylindrical surface on the part in the…

A:

Q: 4X .250-20 UNC-2B 1.260±.010 .984±.010 2.600 ø2.012 2.008 Ø 3.350

A: the position tolerance for the diameter hole  2.012/2.008 and the diameter stud 2.006/2.002 position…

Q: he diameters of shafts with a nominal size of dn = 68 mm must be within limits dmax = 68.045 mm and…

A: Given:dmax=68.045 mmdmin=60.015 mmdn=68 mm

Q: Which position tolerance is shown in below’s technical drawing? Explain the meaning (that is the…

A: Which position tolerance is shown in below technical drawing?Explain the meaning (that is the…

Q: A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing (Figure 1)…

A:

Q: The Boss is created at 59.88, what is the allowed Position Tolerance?

A: Given data as per question Basic size of the boss =60

Q: On the part shown, specify a paralellism tolerance to make the top surface parallel to datum A…

A:

Q: In the following figure, add the tolerance zone and limits of size for both parts.

A:

Q: Using the 10% rule–of–thumb for determining gagemaker’s tolerance for a plug gage, determinethe GO…

A: Given data: Calculate the maximum hole dimension as follows: Calculate the minimum hole dimension…

Q: Explain what is meant by the tolerance percent defective ?

A: I think one word (lot) is missing here. It must be LTPD (lot tolerance percent defective)

Q: What is the philosophy of the Go and No-Gogauging? Complete any missing information on part 182 and…

A: PHILOSOPHY OF GO & NO GO GAUGING:-   1.GO end gauging :-   Go end used in qualify the…

Q: ne 1/2-inch diameter pin in the drawing below is required to be perp ature A within tolerance of…

A: A feature control frame is used to show the conditions and tolerances of the dimension of the part…

Q: If the tolerance in the figure below is for a pin .525 in diameter, what is the total positional…

A:

Q: The nominal size of a hole is Dn = 230 mm. The lower limit deviation El = -0.016 mm, and the…

A:

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: 2. The cross-sectional shape of this feature must be round within a radial tolerance zone of .002"

A: To find:  sketch a feature control frame that matches the description given.: 2. The cross-sectional…

Q: 29. If two planar surfaces are apart from each other by a dimension with a tolerance of t 0.0.05,…

A:

Q: Device need to be placed by Pick and place with accuracy of +/- 50um into nes • Device size = 1.0…

A: The size of device is The tolerance on all sides  is

Q: Identify which is the GO plug and which is the NO GO.   Please explain

A: As per ISO standard design of go-no go gauge will follow as below.for solution refer below images.

Q: Please write the definitions for tolerances, draw the hole shaft basis diagram. Write down different…

A: Definition of tolerances: Tolerancing is genuinely like made tongues. It has its own norms. In a…

Q: What is the Bolt size? (don't worry about the tolerances)

A: As we can see the diameter of the hole is 0.41, so assuming the major diameter of the bolt as 0.41…

Q: The uniform beam has a mass of 41 kg per meter of length. Determine the reactions at the supports. A…

A:

Q: Complete an interpretation drawing that shows the required datum and the perpendicularity tolerance…

A: Perpendicularity: In GD&T the Perpendicularity is defined the two different…

Q: 8. If the limits of size for a hole are .384" and .394" diameter, and the position tolerance is…

A: Write the given data. Minimum limit=0.384"Maximum limit=0.394"Positional tolerance at MMC=0.009"

Q: The dial indicator shows no variation when traversed along the surface of the piece placed over the…

A:

Q: For the geometrical tolerance feature shown, A=4.4, B=0.042, and C=0.00,

A: Given data:

Q: Fill out the table for the shaft-hole assembly Hole Ø 9.12 9.0 Shaft Ø 9.12 8.89 Shaft Hole Limits…

A: Fundamental deviation is the nearest deviation to basic size , It is either lower deviation or upper…

Q: What type of form tolerance is shown in this figure?   Flatness Straightness Cylindricity…

A: Given data : Figure

Q: Given > LMC hole = nominal Ø tolerance True False

A: Here, LMC means the Least Material Condition. 'nominal ∅' represents the nominal diameter. Nominal…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: Calculate the worst-case wall thickness between datum feature B and the 2-inch inside diameter in…

A:

Q: dimension the distance between the holes

A: Bilateral tolerance B = 1.625T = 0.006Bilateral tolerance means that the dimension can vary in both…

Q: II. Comprehensive questions. 1. Explain the meaning of the following annotations, the tolerance…

A: For solution refer below images.

Q: Apply a perpendicularity tolerance to control the pin within a 0.015" cylindrical tolerance zone at…

A: Given:

Q: Refer to the Ø.750 dimension. A) Where is the tolerance specified ?…

A: 1—position 2 – the shape of the tolerance zone

Q: Specify a circularity tolerance of .001 for the conical taper on the part in the drawing below. A.…

A:

Q: On attached drawing 11A017 ,What is the length of the dovetail slot?   All abbreviations are…

A: In the given drawing the length of the dovetail slot is in the side view. The dovetail slot is…

Q: Complete feature control frame that controls perpendicularity of the hole to .012" diameter at MMC…

A:

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types: