4X .250-20 UNC-2B 1.260±.010 .984±.010 2.600 ø2.012 2.008 Ø 3.350

Q: . a. On the part shown, show a angularity specification to orient the angled surface in relation to…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: Figure D1006.02.02 What is the size and quantity of the smallest 52 sized hole(s) in Figure…

A: The size of the smallest size hole is 5 and the quantity is 12

Q: In the following figure, add the largest equal coordinate tolerances so that if two parts are…

A: Maximum distance between mating hole centers, d = 0.5 mmLets assume the equal coordinate tolerance…

Q: I need help figuring out where to place the counterbored hole on the drawing as there is ro referce…

A: Positions of counterbored holes are indicated in the left view of the drawing with the dimensions…

Q: Tolerance Maximum Limit Minimum Limit 57/8" 7'9 1/16" 16.76" 5 13/32" 7'8 15/16" 0.03" 0.007" 0.904"…

A: It is required to complete given table

Q: Refer to drawing 21A044, How many full threads will the fine tapped hole contain at minimum depth…

A: A standard thread form and series, along with allowances, tolerances, and designations, for screw…

Q: What is the LMC of hole D?

A: LMC stands for Least Material Condition, which is the feature of the size of the object that…

Q: What is the philosophy of the Go and No-Gogauging? Complete any missing information on part 182 and…

A: PHILOSOPHY OF GO & NO GO GAUGING:-   1.GO end gauging :-   Go end used in qualify the…

Q: Match each of the following terms to the phrase that describes it. Answers are used only once.

A: The correct match is: Drill spot           -     3Countersink      -     6Knurl                  -…

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: 1. Determine the tolerance allowed on the hole of the part.

A: Tolerance – the total allowable change in measurement; the contrast between the upper and lower…

Q: Find the tolerance and fit type of Ø 60 H7k6,

A: given: nominal size, D=60mm tolerance hub: H7 tolerance shaft: k6 so for tolerance hub: H7, the…

Q: Refer to the 1.914 dimension. A) Where is the tolerance specified ?…

A: A) For MMC  & LMC Consider ϕ0.8740±0.0005 MMC=0.8740+0.0005=ϕ0.8745 LMC=0.8740-0.0005= ϕ0.8735…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance?…

A: Total positional tolerance shows us the maximum allowable deviation of a feature from its true…

Q: -0.0025 1. The dimensions for the shaft size are o50-0.0037 mm and the hole size are +0.000 mm. Find…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: Complete the needed calculations and enter the needed values in the given table. All problems are…

A:

Q: 8. If the limits of size for a hole are .384" and .394" diameter, and the position tolerance is…

A: Write the given data. Minimum limit=0.384"Maximum limit=0.394"Positional tolerance at MMC=0.009"

Q: GER SCALE 9 v 1.3- A 3"-2 ACME .75 1.5 "5 SECTION A-A Ø3.75- D-50 Top and front views of the…

A: Adjusting screw is a screw with threads from 40 to 100 threads per inch. Typically stainless steel…

Q: or a floating fastener application, a hole size specification of 385" minimum and .395" maximum…

A: Given  For hole     Maximum diameter = 0.395 in    Minimum diameter = 0.385 in Find   Final minimum…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: What is the LMC of shaft C?

A: The Least material condition (LMC) tells about the minimum material can be used to produce the…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.