1. 2. Drill spot SR3 3. Countersink Knurl 4. Neck Spherical 5. Keyway 6. Spotface 7. Blind hole 8 Chamfer Counterbore 9 10. > > > > >

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: draw isometric diagram with measurement labels

A:

Q: I keep being told this requires me to make my own drawing, but that is incorrect. The instructions…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A:

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: Assume F-9 kN. Using RECTANGULAR COMPONENTS, determine the direction of the resultant force,…

A: To find: The direction of the resultant measure counter clockwise from the positive x-axis. Given:…

Q: I need answers for problems 1, 2, and 3 pertaining to the print provided.

A: (1). Yes, the detail drawing is of a single part namely the Bonnet Sleeve.

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: the (1) two subscripts and (2) sign of the stress components (\sigma, \tau) under the given…

A: we have to define the state of stress for the given coordinate system

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: I need answers to questions 4, 5, and 6 pertaining to the print provided.

A: Since we question only one question, we will answer the question no. 10. Please submit the question…

Q: A pneumatic system is producing 50 lb/in.2 of gauge pressure. A cylinder is needed to press an…

A: The force produced by the pneumatic cylinder can be calculated using the formula: Force = Pressure x…

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: Need help please all 3 go together

A:

Q: Please use different values. This answer you already gave me for a similar question. These values I…

A:

Q: What type of lines can be used in a drawing to show that part of an object has been removed ?

A: Solution : There are two types of line which are used to show the removed part of an object : Break…

Q: Can I get a more detailled explenation on how to get the numbers in the numetor in each fraction…

A:

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: For problems 1 and 2 below, using the Parallelogram method only (no other method will be accepted)…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.