The tension member is a PL 10x137 of A36 steel. It is connected to a 10mm thick gusset plate, also of A36 steel, with 22 mm diameter bolts as shown below. Determine the nominal block shear strength of the tension member. 37.25 62.5 37.25 O 37.25 75 -0 O -O 75 37.25

The tension member is a PL 10x137 of A36 steel. It is connected to a 10mm thick gusset plate, also of A36 steel, with 22 mm diameter bolts as shown below. Determine the nominal block shear strength of the tension member. 37.25 62.5 37.25 O 37.25 75 -0 O -O 75 37.25

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Block Shear The tension member is a PL% x 5% of A242 steel. It is connected to a %-in. thick gusset…

A: PL 3/8 x 5 1/2 A242 steel3/8 in. thick gusset plate, also of A242 steel, with 3/4-inch diameter.To…

Q: 1. A long tensile member is constructed by connecting two plates as shown. Both plates are made of…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A square hollow section is connected to the flanges of ISMB 600 as shown in the above figure. The…

Q: What is the shear stress in the 25-mm diameter bolt at pin C if P = 25 KN? A 50.93 MPa B 67.91 MPa…

A: Given, dc = 25 mm P = 25 kN

Q: An A36 axially loaded 10mm thick tension member is connected to a gusset plate using 5pcs 20mm…

A: The flexural strength of the section can be found out by the use of the moment of inertia of a given…

Q: The billboard post support a 5KN dead load as shown. The cantilever beam and the brace is pinned…

A: Answer (a) Calculation of ultimate force the brace carries Since the connection is pinned let us…

Q: 4 - The riveted type connection will be used to assemble the given steel members. Determine the safe…

A: Crushing stresses: The compressive stresses at the surface area of contact between the two…

Q: USE NATIONAL STRUCTURAL CODE OF THE PHILIPPINES 2015

A: Given that - To determine the net area for the plate shown in figure . (a) Ag = 2400×14…

Q: Question 3 Determine the capacity of plate! of plate as well as Belts (14) in the below connection…

Q: An eccentrically loaded bolted connection is shown. Diameter of A 325 bolts in standard holes is…

Q: Determine the LRFD design strengths ØP and the ASD allowable strengths P/f of the following section…

A: Answer (a) Fy =345 Mpa, Fu = 450 Mpa Bolt = 22mm tf = 11.18 mm We know that Nominal block shear…

Q: Problem 2. Using 22 mm diameter bolt, compute: a. t for Palone b. t for moment alone c. Critical…

A: Tension member connection and splice: It subjects the bolts to powers that will in general shear the…

Q: The five-bolt connection shown must support an applied load of P = 374 kN. If the average shear…

A: Given data in question Load = 374 kN Shear stress= 321 MPa 5 bolts To find out Minimum diameter of…

Q: A beam to beam joint in bolt connection of single side cleat type is shown in Figure 3. Verify the…

A: Shear resistance : Shear strength refers to a material's or component's resistance to the type of…

Q: For the frame and loading shown, the shear strength of the pins is Trail = 350 MPa. Using a factor…

A: Given, Shear strength τfail=350 MPaFactor of safety =2.5

Q: Determine the adequacy of the hanger connection in Figure Account for prying action. a. Use LRFD. b.…

A: Question is based on hanger connection . Value of dead load , Live load and other dimensions are…

Q: (a) A bolted connection is shown in Figure Q5(a). The 10mm thick plate with grade S275 is bolted to…

Q: snown. 7.12 A built-up steel member is composed of a W18 × 71 wide- flange section with a…

A: Given: To find: The location of the X-X axis.

Q: 2. Problem 7.8-2 Determine the adequacy of the hanger connection in Figure P7.8-2 Account for prying…

A: Question is based on hanger connection . Value of dead load , Live load and other dimensions are…

Q: 4. A flanged bolt coupling consists of eight steel 20-mm vois spdceu evenly around a bolt circle…

A: Given no of bolts =8 Diameter of bolts =20 To fit evenly in circle of 300 mm diameter Sharing…

Q: A C8X11.5 single channel section is bolted to a gusset plate with M22 bolts. Assume A36 steel, 5.6mm…

Q: 2. Problem 7.8-2 Determine the adequacy of the hanger connection in Figure P7.8-2 Account for prying…

A: Flange thickness bf = 4+4+38Flange thickness (bf) = 8.375 inWeb thickness tw = 38+58…

Q: Investigate both the tee and the bolts in the hanger connection in Figure . Include the effects of…

A: Solution a. Use LRFD. b. Use ASD.

Q: Compute the Block Shear Strength of the Tension member 2″4 O O 2" 2" %8-in. bolts L 4x4x2 A36 O 1½"

Q: j) what is the bolt shear capacity of the flange connection in kips? (2 decimal places) A992:…

A: Answer We are given W 16 x 50 beam Flange A 992 (fy = 50 ksi , fu = 65 ksi) Effective bolt hole…

Q: Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm…

A: Member BC: 300mm wide, 10mm plate attached to two 12mm plates at joint C, 3 A490 bolts, A36 plate

Q: 24 kN 3m -3m B 3 kN/m 4 m REDMI NOTE 9 PRO AI QUAD CAMERA

A: The following figure shows the Free Body Diagram of the frame.

Q: Determine the LRFD design strengths ØP and the ASD allowable strengths Pn/ of the following section…

A: Answer (a) We are given W 12 x 30 (Fy = 345 Mpa, Fu = 450 Mpa) bolt diameter = 22 mm thickness of…

Q: 1- A simply supported beam is composed of three plates, which are fastened together using bolts that…

A: We will find maximum shear force in bolt.

Q: A C8X11.5 single channel section is bolted to a gusset plate with M22 bolts. Assume A36 steel, 5.6mm…

A: Given Data : Gross area of the channel = 2181 m2 web thickness = 5.6 mm U = 0.80 shear stress = 457…

Q: If the 18 mm plate is connected to two cover plate of 10 mm on top and bottom, what is the capacity…

Q: Three steel plates are connected using a M24 8.8/s bolt. Determine the design shear capacity of the…

A: Given;Bolt Grade = 8.8Bolt Diameter = M24

Q: (continuation) Determine the shear at 0, in N. O 10 O40 O 30 20 continuation) Find the resultant…

Q: A square hollow section is connected to the flanges of ISMB 600 as shown in the above figure. The…

Q: A joist cutting is used as a bracket to support a load of 135 kN. It is welded to the column flange…

Q: . The welded connection shown in the figure uses electrodes E70XX. The nominal weld strength of the…

Q: 1. Draw the I.L. for the following functions for the girder with the floor system shown below. RD,…

A: We have to draw the Influence Line diagrams for the girder floor system & have to draw the ILD…

Q: 1. The tension member is a PL 1/2 x 10, and the steel is A36. The bolts are 5/8-inch in diam a. Draw…

A: Diameter of bolt=5/8 in Thickness of plate=1/2in To find effective net area

Q: For the connection shown, the average shear stress in the 12-mm-diameter bolts must be limited to…

A: Diameter of bolt d = 12 mmDia of hole =12+1.5=13.5 mmAverage Shear Stress

Concept explainers

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.

Question

The tension member is a PL 10x137 of A36 steel. It is connected to a 10mm
thick gusset plate, also of A36 steel, with 22 mm diameter bolts as shown
below. Determine the nominal block shear strength of the tension member.
37.25
62.5
37.25
O
37.25 75
-0
O
-O
75 37.25

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter. The connection is bottled at the web only. Assume x= 0.76 inch. 2. The shear lag coefficient U and the effective area Ae
1- The bolted type connection will be used to assemble the given steel members. Determine the safe load that a single turned bolt can carry. Consider only the effect of shear stresses. (St-37, H) t= 20 # ##* JL 90.90.9 40 50 315 9,96 t 9,04 t 9,40 t 9,70 t
#9
Determine the maximum service load P (ASD) that the connection can resist. Use 27 mm Ø A490-N bolts, and 10 mm A-36 plate and a load P with a slope 1H: 2V. Assume that edge distance and bolt spacing are not critical. ***Note: Lod P is acting at a slope of 1H: 2V
Determine the required diameter of the bolts to be used in the bracket shown if it has a allowable shearing stress of 93 Mpa. The bracket carries an eccentric load of 50 kN.
Please show solutions on how to get the 0.250 value. The circle green in the figure. Civil engineering- steel design
10) what is the bolt shear capacity of the flange connection in kips? (2 decimal places). A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
PLEASE ANSWER THIS QUESTION ASAP!!!
Compute the nominal strength based on yielding in KN. Determine the allowable tensile strength of Plate A in KN. Compute the allowable tensile strength at section a-1-2-2-4-c in KN.
11-12. A joint is fastened together using two circular bolts. A single plate carries 40 kN load. What is the actual shear stress if the allowable shear stress is 350 MPa and factor of safety is 2.5? A350 Pa CS with 6.5T5MP C. 140 Pa B. A D. 965 MPa Determine the diameter required using the actual shear stress. B. 8.53 mim C. 12.06 mm A. 13.49 mm D. 19.07 mm
• Compute the available block shear strength of the connection based on the KN. (Diameter of hole is 20mm, ST37 steel is used, and thickness of plate is 7.5mm) 2@75 mm 3@75 mm
An A36 axially loaded 12mm thick tension member is connected to a gusset plate using 5pcs 20mm diameter rivets arranged as shown. Use Fy= 248MPa & Fu=400MPa for the steel plates. Given a=67mm, b=99mm, c=67mm, x=76mm, y=68mm and z=63mm. Considering the green shaded area to be in Block Shear Rupture (BSR), where its nominal block shear strength can be calculated using Rn=0.6FuAnv+UbsFuAnt . Calculate the net area along tension surfaces, Ant in mm2. Express your answer in whole number.