11-12. A joint is fastened together using two circular bolts. A single plate carries 40 kN load. What is the actual shear stress if the allowable shear stress is 350 MPa and factor of safety is 2.5? B. MPa D. 965 MPa CS 8.575 140 MPa A. 350 V Determine the diameter required using the actual shear stress.

11-12. A joint is fastened together using two circular bolts. A single plate carries 40 kN load. What is the actual shear stress if the allowable shear stress is 350 MPa and factor of safety is 2.5? B. MPa D. 965 MPa CS 8.575 140 MPa A. 350 V Determine the diameter required using the actual shear stress.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5) Complete solution and correct units pls. Thanks
Given a 10"X16" reinforced concrete beam section as shown. The main reinforcing rebars consist of two #6 (each #6 bar has a section area of 0.44 square inches). Concrete fc'=3000 psi. Rebar yield strength fy=60 ksi. What is the section's theoretical nominal bending moment capacity in ft-k? loll O A. 65.8 ft-k. OB. 57.0 ft-k. OC. 34.1 ft-k. OD. 29.7 fft-k. X²N 16"
Need urgent answer. Don't provide wrong answer.
A flexural member is fabricated from two flange plates 1/2in x 16in and a web plate 1/4in x 20in. The yield stress of the steel is 50 ksi. a. Compute the elastic section modulus S and the yield moment My with respect to the major principal axis. b. Compute the plastic section modulus Z and the plastic moment Mp with respect to the major principal axis.
help match please
3. A flat steel bar, I inch wide by 1/4 inch thick and 40 inches long, is bent by couples applied at the ends so that the midpoint deflection is 1.0 inch. Compute the stress in the bar and the magnitude of the couples. Use E 29 x 106 psi. (Practice at Home) M 20" Cross Section P-1 20" 1/4" M
Read the question carefully and give me right solution according to the question. Thank you
cd efgh ij O klmn u op V 0 0 0 t Р What is the line for which the section will rupture in tension? All holes are the same diameter. m n j h d
Need complete and elaborate solution A.Using ASD, check the adequacy of the base plate (PL400x350x19 mm) centered on a W12X152 column as shown. It is resting on a concrete pedestal that is 450 mm x 400 mm. The loads are PDL = 600kN and PLL = 320 kN. Use A-36 steel and concrete fc’=20 MPa. B. Using LRFD, PL400x350 mm base plate, W12x120 column, 500x500 mm pedestal, PDL = 1200 kN and PLL = 800 kN. Use A-50 steel and concrete fc’ = 30 MPa. Determine the required base plate thickness.
Hello, Please help in solving this question. Add Fbd if possible
Need urgent answer Don't provide wrong solution
SOLVE THIS PROBLEM USING THE SLOPE DEFLECTION EQUATIONS: The bearing type connection show is bolted by 4 – 22 mm diameter bolts (high strength bolts). The size of the plates is 300 mm x 12 mm. Fy 248 MPa, Fn = 330 MPa and Fu = 400 MPa. Determine the following: (1) Design strength of the connection based on strength of plates. (2) Design strength of the connection based on shear strength of bolts. =0.65. (3) Design strength of connection based on bearing strength of bolts on the 12 mm plate. =0.75 12 mm P. mm O. O 300 mm 40 80