art A The assembly consists of two posts AD and CF made of A-36 steel and having a cross-sectional area of 1100 mm², and a 2014 aluminum post BE having a cross-sectional area of 1700 mm². If a central load of 400 kN is applied to the rigid cap, determine th stress in each post. There is a small gap of 0.12 mm between the post BE and the rigid member ABC. (Figure 1) Enter your answers, separated by commas. OAD, CF, OBE = Submit 15. ΑΣΦ | 11 Ivec My Answers Give Up SHIND ? MPa

art A The assembly consists of two posts AD and CF made of A-36 steel and having a cross-sectional area of 1100 mm², and a 2014 aluminum post BE having a cross-sectional area of 1700 mm². If a central load of 400 kN is applied to the rigid cap, determine th stress in each post. There is a small gap of 0.12 mm between the post BE and the rigid member ABC. (Figure 1) Enter your answers, separated by commas. OAD, CF, OBE = Submit 15. ΑΣΦ | 11 Ivec My Answers Give Up SHIND ? MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear strain in the shear plane of the bolt when the applied force P = 750 kN is removed. Note: The bolt is made from a material having a shear stress-strain diagram as follows T (MPa) A { 600 400 5 50 y (10³ rad)
solve the problem
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.35 in., a wall thickness of 0.07 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.3 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
2.)
Please show your solution on a paper with FBD
Mechanics of deformable bodies.
The axial load 396 kN applied to the lap joint is distributed equally among the three 20.6-mm-diameter rivets. What is the maximum tensile stress (in MPa) in the plate if w = 135.4mm and t = 27.1mm? Round off the final answer to three decimal places.
PLEASE ANSWER ASAP TY! a) Determine the cross-sectional area of the structural tube (in mm2) b) Determine moment of inertia of the cross-section about the neutral axis (in mm4) c) What is the maximum normal stress at point K (in MPa)? Include negative sign if compressive. d) What is the axial stress at section H-K (in MPa)? Include negative sign if compressive. e) What is the flexural stress at section H-K (in MPa)? f) What is the maximum normal stress at point H (in MPa)? Include negative sign if compressive.
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
Problem 01.054-Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view. 160 mm D B 18 mm B Top view 120 mm largest load P that can be applied at A is 99252 2.328 KN. ED 6 mm 22B Side view
Urgent please solve quickly. a = 10 , b = 7 solve this question about this information. Extra information: Take both loads 35 kN