Problem #4: The aluminum shaft consists of two segments AB and BC (G = 27 GPa). Shaft AB is a solid shaft with a diameter of 60 mm. Shaft BC is a hollow shaft with an outside diameter of 60 mm and an inside diameter d₂. If the total angular deformation from A to C is not to exceed 4.30⁰, determine the value of d₂. Express the answer to the nearest even number. Using the value of d₂, calculate the amount of shear stress developed in segment BC. [d₂ 60 mm 1.15 m B 245 N-m 0.75 m 635 N-m da

Problem #4: The aluminum shaft consists of two segments AB and BC (G = 27 GPa). Shaft AB is a solid shaft with a diameter of 60 mm. Shaft BC is a hollow shaft with an outside diameter of 60 mm and an inside diameter d₂. If the total angular deformation from A to C is not to exceed 4.30⁰, determine the value of d₂. Express the answer to the nearest even number. Using the value of d₂, calculate the amount of shear stress developed in segment BC. [d₂ 60 mm 1.15 m B 245 N-m 0.75 m 635 N-m da

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
A square plate O-P-Q-R of a linear elastic material with sides 1.0 m is loaded in a state of plane stress. Under a given stress condition, the plate deforms to a new configuration O-P'-Q'-R' as shown in figure (not to scale). Under the given deformation the edges of the plate remain straight. 10 mm y4 R'. Q' 10 mm R Q 10 mm P 20 mm The horizontal displacement of the point (0.5 m, 0.5 mm) in the plate O-P-Q-R (in mm, round off to one decimal place) is
STRAIN
2. Solve for the deformation of the aluminum rod. 200 mm 300 mm 600 kN Aluminum E= 70 GPa A= 900 mm Steel E= 200 GPa A=1200 mm
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown below. Axial loads are applied at the positions indicated. Find the maximum value of P in Newton that will not exceed a stress in steel of 150 MPa, in aluminum of 87 MPa, or in bronze of 97 MPa.
A symmetrical framework consisting of three pin-connected bars is loaded by a forceP (see figure). The angle between the inclined bars and the horizontal is a = 52°. Theaxial strain in the middle bar is measured as 0.036.Determine the tensile stress in the outer bars if they are constructed of a copper alloyhaving the following stress-strain relationship:
30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? E= 6/8 v = -E(lateral)/(axial)
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P in kN that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa
A steel with E = 29 000 ksi with a rectangular cross-section is bent over a rigid mandrel with R = 15 in as shown in the figure. If the maximum flexural stress in the bar is not to exceed the yield strength of 36 ksi, determine the allowable thickness h of the bar.
8. A rigid bar AB is supported by three rods. A load P = 250 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10°6 kN/m^2 and modulus of elasticity of steel is 200 x 10°6 kN/m^2. Steel rod A= 900 sq. mm Steel rod A= 900 2m sq. mm Copper A=1200 sq. mm 2m B 1m 1m Determine the deformation in the rods (in mm). * Your answer
10
An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m; B2 = 1.0 m; B3 = 0.6 m. Determine the total deformation of the bars B1, B2 and B3 in mm. 35KN B1 B2 B3 10KN 15KN 30KN 2.5 B 1.79 C) 0.54 3.75 E 4.83