Result Reviewer VI. Knowing that for the beam shown. The allowable stress is 80 kPa in tension and 160 kPa in compression, yı 52mm, y2-88mm, Iz-763cm4. Please determine the largest force F that can be applied to the beam. (unit:kN, and accurated to 2 decimal place) í 2m 2m 2m

Q: IS 25 kg and it causes each spring to be stretched by 500 mm, vhen the 2 blocks are applied; (2) the…

A: Draw the free body diagram at A           apply equation of equilibrium ∑Fx = 0 -TAB cosθ+TADcosθ =…

Q: For the loading shown, use the double-integration method to determine (a) the equation of the…

A:

Q: SITUATION. A square footing is to support a 400 mm x 400 mm column carrying 1400 kN live load and…

A: Given:  Dia of bar = 28 mm  Strength of concrete in column and footing = 28 mpa and 21 mpa…

Q: All values of Stz are by the joint on the part indicated. What is the missing value? ? 0 O-6a²t 4a²t…

A: The given figure;

Q: A motorist driving a 1000-kg car wishes to increase her speed from 20 m/s to 30 m/s in 5 s.…

A: Given,m=1000 kgu= 20 m/sv=30 m/st=5 s

Q: A plate 0.03 mm distant from a fixed plate, moves at 80 cm/s and requires a force of 4 N per unit…

A:

Q: Which condition would require decreasing the mixing speed in the slow mixing tank? * Warm inlet…

A: Introduction : Prior to sludge thickening or dewatering, slow mixing or flocculation tanks are used…

Q: 5. Draw the FDBS of member ADB and BEC 1m 1m В E 1 m D 1.6 m A

A:

Q: 49. A man wishes to prepare the future of his ten-year old son. Determine the monthly savings that…

A: Solution: Given: Amount = 120000 Interest = 5.41% Time period = 18-10=8 years

Q: F, F, 4. 3 m 3 m Given F1 = 933 N, and F2 = 961 N, What is the total moment produced by the two…

A:

Q: An open cylindrical tank, 2 m in diameter and 4 m high contains water to a depth of 3 m. It is…

A:

Q: In the cost assignment matrix below, the best strategy to assign contractor to contract is. *…

A: For the given cost matrix, performing the balanced minimization.  Row reduction: It is done by…

Q: Figure 2.1 shows the general arrangement of a cantilever retaining wall. You may assume the unit…

A: Solution:

Q: Classify structure if statically determinate, statically indeterminate, unstable. if indeterminate…

A: For any plane structure to be stable externally, minimum 3 number of reactions are required.…

Q: For the joint in the figure below find T3 (only) knowing that: T1 = 8.8 N Angle between the T2 and…

A: To find value of T3

Q: (Perfect Score in the Final Exam) Find the approximate value of the Moment at Point A using Shear…

A: ###Determination of moment at A using BMD and SFD ####

Q: The centripetal force on a car rounding a curve on a level road is provided by O Friction between…

A: Given :- the centripetal force on a car rounding a curve on a level road is provided by :

Q: If the total weight of the lift (carried by both chains) is 6,038 Ibs, and the angle O is 56°, what…

A: The total weight of the lift = 6.038 lbs Each chain will carry half the total weight of lift (3.019…

Q: The Atterberg limits of a soil sample are: Liquid limit, w₁ = 50% Plastic limit, Wp = 30% Shrinkage…

A:

Q: A plate 0.03 mm distant from a fixed plate, moves at 80 cm/s and requires a force of 4 N per unit…

A:

Q: Calculate the torsion constant, J, for the below thin-walled closed cell where a = 40mm and t =…

A: a = 40 mm t = 0.7 mm Free body diagram:

Q: 20 kN 3 m 3 m 60° 60 3 m 10 kN 10 kN

A:

Q: A rectangular concrete beam 120 x 300 mm is prestressed by straight cable, effective force 180 kN at…

A:

Q: A flexible cable is subjected to a uniformly varying load. If the tension at the supports is 12 kN,…

A:

Q: The magnetic bearing of line XY was observed to be S 31° W, when the declination was 2° E. Point Z…

A:

Q: X acquires a coalmine at a cost of $1,660,000. Intangible development costs total $540,000. The…

A:

Q: L, Structural Select, sawn lumber beam? O 13.8 MPa O 16.5 MPa O 18.3 MPa O 10.0 MPa O 19.5 MPa O…

A: A timber is defined as the sawn wood that is used in the form of a structural member having the…

Q: D Draw the force diagram of member AB and CD. F C A B

A:

Q: Determine the moment of inertia of the composite figure about an axis through its centroid and…

A:

Q: Compute the moment of inertia about the centroidal x-axis 6 in. 6 in. 4.5 in. 3 in.

A:

Q: THREE PIPES A, B, AND C ARE TANGEN EXTERNALLY TO EACH OTHER AND EACH TANGENT INTERNALLY TO A LARGER…

A: Solution- Given, D =250 N Weight of A=300 N Weight of B and C=200N The radius of A =5 cm

Q: Construct Free Body Diagrams (FBD) of typical 12' and 16' joists and the interior beam along grid…

A: According to given data  Construct Free Body Diagrams (FBD) of typical 12 and 16' joists and the…

Q: mine the resultant couple e into x and y components and g the and y -2 ft t nts 1 ft 80 lb 80 lb S S…

A:

Q: Consider the cold-formed section shown below: 2 mm write ¹25 mm 20 mm 15 mm 25 mm 25 mm 15 mm What…

A: Diagram of of a cold formed section  Maximum torque = 65 N m or 65000 N mm

Q: For a trapezoidal channel having discharge 14 m'/s. It have sluice gate opening 0.5 m. The channel…

A: Given Q = 14 m3/s B = 6m S0 = 0.0033 n = 0.024 Side slope = 1H : 2V S0, z = 1/2 =0.5 First find…

Q: Given: A W12x79 column with lateral supports at mid-height, as indicated below. Non-slender?(y/n).…

A: W12x79 Column: Ag= 26.5 in2 rx= 6.14 inry= 3.7 in

Q: According to Francis Ching, what is an interior elevation? An orthographic projection of a…

A: Francis D.K. Ching was a registered architect and a well known Professor Emeritus at the University…

Q: PROBLEM : FIND THE NUMBER OF 50K8 BAGS OF CEMENT, SAND AND GRAVEL WITH A CLASS "B" MIXTURE OF THE…

A:

Q: An internal twisting moment of 1500Tt N-m is applied to the shaft shown below. Determine the…

A: Calculate the polar moment of inertia of the given circular section,  J = πd464   =π×100464…

Q: Result III. A ladder shaped rod ABC is subjected to axial loads as follows, F=10kN₂11-12-400mm,…

A: F=10kN , l1=l2=400mm , A1=100mm2 , A2=50mm2 , E=200GPaTo Find :a) Axial force diagram for the rod.b)…

Q: Question 3 a) From Experimental investigations it is known that the pressure drop per unit length…

A: Given data, Pipe diameter = d Average roughness height = Ks Flow velocity = V Density = ρ Viscosity…

Q: he following picture shows part of a beam section which has been structurally idealised. The skins…

A: The term shear flow refers to the distribution of shear stress within a thin-walled structure caused…

Q: Draw the node diagram and perform the CPM computations for the sche shown next. ACTIVITY IPA…

A: ES = Earliest Start Time EF = Earliest Finish Time = ES + DurationLF = Latest…

Q: Combined Stress: 17a The cantilever beam shown below is loaded by P=20 kN load as shown. Find at…

A: Load, Normal stress, Width of section, Depth of section, To find: The angle to produce zero normal…

Q: The radius of the path of an object in uniform circular motion is doubled. If its speed remains the…

A: The radius of the path of an object in uniform circular motion is doubled. If its speed remains the…

Q: A trapezoidal canal with a base of 2.0 m has its sides sloping at 45* with the horizontal. If water…

A: Given that, for the trapezoidal canal,  base, b = 2 m  side slope, θ=45° depth of flow, y = 1 m The…

Q: Consider the beam shown in the figure Given: P-8 kips. w-3 kipvft 16' NOTE: This is a multi part…

A:

Q: 2. The following results were obtained from liquid limit and plastic limit tests conducted on the…

A:

Q: Problem 1: For the shown beam: a. Calculate the Equivalent Concentrated force FR for the 5 KN 4.0…

A: We are authorized to answer one question and three subparts at a time since you have not mentioned…

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.