L Br St 0 16 P 09 Br Find the stress in each rod Given: Ast = Abr=200mm² Est = 200 G Pa Ebr = 83 GPG P= last 2 digits of Stud no. +8 (KN) L= last digit of studen- no. +2 (m) P=43+2=51 L = 43 +2 = 45

Q: The simply supported beam in Figure below has a rectangular 3kN w = 1.5 kN/m cross section 100 mm…

A: Finding out maximum stress.

Q: In terms of w, L, E, and I, determine the deflection and slope at x = L of the beam shown in Figure…

A: Draw the free-body diagram of the beam.

Q: What is the prestress steel loss from steel relaxation at 356 days for a Grade 270 low-relaxation…

A: Given:- Initial stress = 190,000 psi Yield stress = 245,000 psi Time period = 356 days To…

Q: Refer from the figure shown below: a.) What force F must be applied to the following static…

A:

Q: Pipe Water Ah SG = 2.6 D = 30 mm Figure Q2 (a)

A:

Q: Determine the magnitude of the resultant force acting on the hook in N if F 430 N and F= 260N 30° 30…

A:

Q: For a certain two-dimensional incompressible flow, velocity field is given by 2xy i - y2j . The…

A:

Q: answer quickly

A:

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A:

Q: A beam is limited to the dimensions b = 15 in, d = 20 in,. and d' = 4 in. If Mp = 170 kip-ft…

A: We have to determine the value of limiting steel ratio maximum steel area based on steel ratio and…

Q: For the pulley system shown in the figure below, which of the following statements are true?

A: Consider the FBD of pully A

Q: 6. Design a circular sedimentation tank with a retention period of two hours for a town with a…

A:

Q: 1O N A GN

A:

Q: Determine the minimum force P to prevent the 399-kg rod AB from sliding. The contact surface at B is…

A: Take moment about B:∑ MB=0NA3+fA4-mg42=0NA3+0.45NA4-399×9.8142=0NA=1630.9125N

Q: A simply supported beam, 300 mm x 600 mm in dimension as shown in Figure 2, is prestressed by a…

A:

Q: Calculate the shear force and bending moment for the beam subjected to the loads as shown in the…

A: Given; FBD of beam:-

Q: Classify the following soils by the (1) USCS and (2) AASHTO classification system and give the group…

A: AASHTO soil classification system is based on,  Grain size distribution  Atterburg's limits…

Q: A 6.0m long simply supported reinforced concrete beam has a width of 350mm and an overall depth of…

A: Given : 350 X 470 mm beam, fc = 20.7 MPa, fy = 415 MPa 4 - 28 mm dia bars in tension side and 2 - 28…

Q: Q.1 At a point in a material there is a horizontal tensile stress of 150 MPa, a vertical compresaive…

A:

Q: Calculate the Shear Force at point A of the following Beam. Take X=35 kN and Y=80KN YKN X kN/m A, D…

A: Given, Beam,

Q: (c) An analysis of a water sample has produced the following concentrations, as shown in Table 1(c).…

A:

Q: A 50 mm2 steel bar in a machine structure is 1 m long. It has to resist a strain energy of 100 Nm…

A: Given data, Area of steel bar = A = 50mm² L= 1m = 1000mm Strain energy= u = 100Nm = 100×10³N-mm Fos…

Q: Use Area-Moment Method. E = 200 GPa and I = 90 x 10® mm“. Determine the rotation at A in degrees.…

A: Solution:- The given diagram is shown below,

Q: and trailer cO le is 4 kips, the

A:

Q: Question For a certain loading condition, a saturated clay layer undergoes 40% consolidation in a…

A: Given data- A saturated clay layer- Consolidation=40%, Time period t=178 days, To Find- The…

Q: Set up the appropriate equation that is used to solve for the moment of inertia about the y axis.…

A:

Q: If A is a 3 x 3 matrix such that A= 3, then 2adjA|

A:

Q: Determine the force in each member of the loaded truss. Th 2250 N -189m h-38m A- 46° F

A:

Q: The cable is subjected to the uniform loading shown below. Determine the following: a) Maximum…

A:

Q: Q2. (a) Determine the maximum deflection of a cantilever beam at its free end subject to a uniformly…

A:

Q: Determine the force in each member of the truss, and state if the members are in tension or…

A:

Q: Air flows at the rate of 1.5 m3/s through a horizontal pipe with a gradually reducing cross-section…

A:

Q: The three hinged spandrel arch is subjected to the loading shown. Determine the following: a)…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub- parts for…

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.