For the two lane highway below, determine the distance required to transition pavement cross-slope of 2% to superelevation of 8% (i.e., find the distance from staNC to full superelevation). The design speed is 50 mph. Two Lane Highway Sh Lane Lane Sh Normal Crown 0.02% 0.02% 0.00% Flat Crown 0.02% 0.02% Reverse Crown 0.02% Full Super e

For the two lane highway below, determine the distance required to transition pavement cross-slope of 2% to superelevation of 8% (i.e., find the distance from staNC to full superelevation). The design speed is 50 mph. Two Lane Highway Sh Lane Lane Sh Normal Crown 0.02% 0.02% 0.00% Flat Crown 0.02% 0.02% Reverse Crown 0.02% Full Super e

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The allowable distance from a roadside obstruction to the centerline of the inside lane of a proposed highway (horizontal curve) is 86.0n The current design plan of the highway horizontal curve has a radius of 695 n. for a level grade, with a design speed of 65 mph. Braking friction coefficient f-0.35, side friction coefficient f-0.11, superelevation rate e6. Please check the design adequacy for the radius of the curve.
Calculate the extra width of the pavement required on a horizontal curve of radius 700 m on a two lane highway, the design speed being 80 kmph. Assume wheel base length of 6m
What is the extra widening required (as nearest magnitude) for a pavement of 7 m width on a horizontal curve of radius 200 m, if the longest wheel of vehicle expected on the road is 6.5 m and the design speed is 65 km/m?
Find out the length of the transition cruve for a horizontal curve. The horizontal curve external distance 20 m and central angle 4=30°. The width of the pavement 7.3m. Extra widening 0.7m. design. Speed 30 Km/h. Superelevation = 7%.
7. What is the psychological widening of a pavement on horizontal curve of radius 230m for ruling speed 80 kmph?
THE RADIUS OF HORIZONTAL CURVE IS 400M, THE TOTAL PAVEMENT WIDTH AT CURVE IS 7.6M AND THE SUPER ELEVATION IS 0.07. DESIGN THE TRANSITION CURVE LENGTH FOR A SPEED OF 100 KMPH FOR PLAIN TERRAIN. ASSUME PAVEMENT TO BE ROTATED ABOUT THE INNER EDGE. EXTRA WIDENING NEED NOT TO BE CONSIDER.
2. Calculate the total stopping sight distance for a wet pavement condition, if the design speed is 100 Km/hr for the following three conditions. a. Road is flat b. The road has a 6% downslope c. The road has a 3% upslope
3) A rural arterial is expected to carry an ESAL of 1.88x10 during the 1st year of operation with an expected traffic growth rate of 5% over 30-years of design life. If the M, of the subgrade is 103,500 kN.m2, design a suitable flexible pavement consisting of granular subbase with a material layer coefficient of 0.13, a granular base layer with a material layer coefficient of 0.14, and an asphalt surface layer with EAC of 2,760, 000 kN/m2. Assume the drainage coefficient = 1.0, percent traffic on the design lane = 47%, and design serviceability loss - 1.7.
(b) While aligning a high way in a built up area, it was necessary to provide a horizontal circular curve of radius 325 metre. The design speed is 65 kmph, length of wheel base of largest truck = 6.0 m and width of pavement is 10.5 m. Design the following geometric features: (i) Superelevation (ii) Extra widening of pavement (ii) Length of transition curve.
You have been tasked as a Highway Engineer to undertake the geometric design of the Block Factory road which is a collector road leading to AIT Seaview Campus in Accra using a design speed of 60km/hr, superelevation of 5% and trailer as design vehicle. Specify the desirable values to be employed for the following design elements: (AP,5)i. Maximum standard gradientii. Minimum vertical curve lengthiii. Minimum horizontal curve radiusiv. Curve widening amountv. Single carriageway width