Find the total width of a two lane, no kerbs pavement on a horizontal curve along a national primary road with rolling topography. Use distance between two wheels = 6 m, superelevation= 0.07, skid resistance = 0.15. (Hint: Use IRC values for normal width of a road)

Find the total width of a two lane, no kerbs pavement on a horizontal curve along a national primary road with rolling topography. Use distance between two wheels = 6 m, superelevation= 0.07, skid resistance = 0.15. (Hint: Use IRC values for normal width of a road)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q9: Calculate the right of way of rural divided four-lane highway has depressed median and it is constructed on embankment. The median width is 4.0 m, embankment height is 6m, lane width is 3.5 m, shoulder width is 2.60 m and side slope is 1:3 (V:H).
Find out the length of the transition cruve for a horizontal curve. The horizontal curve external distance 20 m and central angle 4=30°. The width of the pavement 7.3m. Extra widening 0.7m. design. Speed 30 Km/h. Superelevation = 7%.
Design a Two way - one lane Highway with the following specification. V= 90 kph e=0.05 m=15 m SD=115 m wheel base = 2.25 m C=3 Pavement is rotated at center I =20 Determine the following: Minimum Radius Road Widening Transition Spiral (if any) Vertical Curve Tangent and Length of Curve Road Profile for horizontal alignment with station if the start station is 1+ 000
A temporary, 2 lane road is to be built connecting the 2 westbound lanes of Highway 1 near Tompkins, Saskatchewan with the parallel 2 eastbound lanes, 600 metres to the south (centreline to centreline). This temporary road is comprised of two equal circular, horizontal curves connected by a tangent section, which has a bearing of 045°. For the following data: radius of curvature=500m; maximum superelevation=0.04m/m; maximum side friction=0.12; lane width=3.70m. Find: i) the design speed of the curved sections and ii) the total length of the new pavement required
2. Calculate the total stopping sight distance for a wet pavement condition, if the design speed is 100 Km/hr for the following three conditions. a. Road is flat b. The road has a 6% downslope c. The road has a 3% upslope
Give me right answer with explanation
The braking distance of a car from 120 km/h is 50 m assuming the pavement is level. (a) if the pavement is with 6° inclination, what will be the braking distance (in meter) of the car going up from 120km/h? (b) and if the car is going down at 2% inclination, what is its braking distance (in meter) from 120km/h? Note: Assume the breaking force is not dependent of the grade.
You have been tasked as a Highway Engineer to undertake the geometric design of the Block Factory road which is a collector road leading to AIT Seaview Campus in Accra using a design speed of 60km/hr, superelevation of 5% and trailer as design vehicle. Specify the desirable values to be employed for the following design elements: (AP,5)i. Maximum standard gradientii. Minimum vertical curve lengthiii. Minimum horizontal curve radiusiv. Curve widening amountv. Single carriageway width
Question 21 Calculate the design thickness in mm (rounded to the nearest tens) at the center of a rigid pavement with dowels if the: Allowable tensile strength of concrete = 3.0 MPa Wheel load = 117 kN • Question 22 A vehicle encounters a sag parabolic curve on a night travel. The stationing at the vehicle at the point of study was 1349+998 meters and the stationing at the end of the curve is 1350+103. If the sight distance following standard design values is 114 meters, what is the value of the change of grade A in %?
Q5/ A- A highway section. +2%, meet -8% at point with 52.0 m at speed 110 Km/hr. Determine the elevation of the highest point on the pavement surface within this
Please correct solution